User manual DENON RC-8000

[. . . ] REMOTE CONTROL UNIT RC-8000 OPERATING INSTRUCTIONS MODE D'EMPLOI ¥)) FOR ENGLISH READERS POUR LES LECTEURS FRANCAIS PAGE 42 ~ PAGE 33 PAGE 34 ~ PAGE 65 "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" "NO. DE SERIE PRIERE DE NOTER LE NUMERO DE SERIE DE L'APPAREIL INSCRIT A L'ARRIERE DU COFFRET DE FAÇON A POUVOIR LE CONSULTER EN CAS DE PROBLEME. " ENGLISH 2 We greatly appreciate your purchase of this unit. 2 To be sure you take maximum advantage of all the features this unit has to offer, read these instructions carefully and use the set properly. [. . . ] w Press the "Add" button on the system call selection screen to set the mode for inputting buttons to be registered in the system call setting. e Select the buttons whose signals you want to store at a system call button. The device registered at the top of the icon display section is displayed first. (By default, AV amplifier page 1 is displayed. ) Here, press the AV amplifier "ON" button and the "DVD" button. To select other devices, press the JOG switch's ENTER button to display the icon display section, then select the device. Screen w Screen e 20 ENGLISH r Press the and buttons in the icon display section to display the DVD icon, then press the DVD icon to select it. To select buttons on other pages, press the JOG switch's left and right buttons to switch the page. When the "END" button is pressed, the display switches to a confirmation screen. t The buttons registered in steps e and r are displayed on the confirmation screen. The system call signals are stored at the open system call button with the lowest number. Screen r Screen t [3] Editing registered system call settings q Press "SETUP" on the icon display section for 3 seconds to display the setup screen. Call Setup" button on the "Setup 3/4" page to display the system call selection screen. w Press the and buttons on the call list to display the system call button you want to edit. Press the system call button you want to edit so that it is displayed in half-tone dot mesh, then press the "EDIT" button to set the system call edit mode. e Editing system call settings e-1 Changing the delay time By default, the delay time is set to 0. 7 seconds. The delay time can be changed to anything between 0 and 10 seconds in steps of 0. 1 second. The delay times at the right of the buttons indicate the time from which the signal for that button is sent until the signal for the next button is sent. Press the button on the system call editing screen's button list whose delay time you want to change so that it is displayed in half-tone dot mesh. Press the · and ª buttons at the bottom right of the editing screen to set the desired delay time. Screen q Screen w Screen e 21 ENGLISH e-2 Deleting buttons a. At the system call editing screen, press the button you want to delete so that it is displayed in halftone dot mesh. At the system call editing screen, press the button you want to move so that it is displayed in halftone dot mesh. Press the "Move" button, then press the button at the position to which you want to move the first button. The first button is inserted at the position before the second button. [. . . ] AC 120V 60Hz AC OUTLETS To REMOTE IN terminal 3 ENGLISH Connecting to Other Devices Use the procedure described below to connect the RC-8001ST to a Denon device not equipped with a REMOTE IN terminal or to other devices. q Connect the included AC adapter to a wall power outlet, then connect the power cord to the RC-8001ST's DC IN terminal. w Connect a commercially available IR emitter (a Denon RC-618 for example) to the RC-8001ST's EMITTER terminal, then place the IR emitter near the device's remote control receiver in a position in which reception is possible. ANOTHER ROOM MULTI SOURCE AUDIO signal cable MAIN ROOM EMITTER terminal RC-618 RC-8000 RC-8001ST Connecting Using a Denon RC-616 The following shows an example for controlling multiple devices using a Denon RC-616 powered emitter. RC-8000 WIRED terminal PARALLEL IN terminal RC-618 RC-8001ST RC-616 4 ENGLISH 5 OPERATION About the RF Transmission Function RF transmission is possible when the RC-8001ST is used in combination with the RC-8000 (included with the AVR5800 or sold separately) remote control transmitter. [. . . ]