User manual DENON POA-T3

[. . . ] Cleaning ­ Unplug this product from the wall outlet before cleaning. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture ­ Do not use this product near water ­ for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. Accessories ­ Do not place this product on an unstable cart, stand, tripod, bracket, or table. [. . . ] IN subwoofer terminal. Option Setup Setting the Volume Control This sets the volume level of output. 1 Option Setup 1 Press F G to set. +15 dB, +10 dB, +5 dB, 0 dB: Sets the playback level of the analog signal that was input to the EXT. 2 Press D H to select the item, then press F G to set. Volume Limit: Set the volume's upper limit. · 0 dB, ­10 dB, ­20 dB: The volume cannot be increased above the selected levels. · OFF: If you do not want to set a volume limit, select "OFF". In this case, the volume can be set to the POA-T3's maximum volume (output) level of +18 dB, which is extremely loud. Power On Volume Level: · LAST: The volume set when the POA-T3 was last used is stored in the memory and set when the power is turned on. · ­ ­ ­ (Mute): The volume is always muted when the power is turned on. · ­80 dB ~ +18 dB: Set the volume level when the power is turned on. You can adjust the volume level within the range of ­80 to +18 dB. · ­40 dB, ­20 dB: The volume is lowered 40 dB or 20 dB from the current level. 2 1 Limit -10dB 2 P. On LAST H to enter the 2 Press ENTER orMemory setting. setting and switch to the Auto Preset 3 Mute FULL 3 4 AutoSurr. ON 1 6 EXT. In SW +10 2 7 Preset <Start Setting the Auto Surround Mode Set whether or not to store the surround mode last played for the input signal. If so, play in the "DTS" mode. DIMMER INPUT SELECTOR To lower the subwoofer channel level in the EXT. For some players the playback level of the SW channel may seen strong. If so, set to "ON". SURROUND PARAMETER INPUT MODE About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit 3 Start playback on the selected component. For operating instructions, refer to the component's manual. 21 ENGLISH ENGLISH Basic Operation Basic Operation Turning the sound off temporarily (MUTING) Press [MUTING]. You can adjust the muting level ( page 20). Checking the currently playing program source, etc. Press STATUS. · The current program source and various settings are indicated on the display. Sources recorded in stereo Sources recorded in monaural DIRECT / STEREO ( page 23) · Effective for achieving pure playback. · If there is no need for tone control or distribution of the low frequencies in function of the speaker configuration, select the DIRECT mode to achieve the best sound quality. DENON Original Surround Modes ( page 28, 29) · Select these for 5. 1-channel playback with sources recorded in stereo or monaural. DTS NEO:6 ( page 25) · This is a surround mode for playing 6. 1-channel stereo sources developed by Digital Theater Systems. · One of two playing modes, MUSIC (for music sources) or CINEMA (for movie sources), can be selected according to your preferences. DOLBY PRO LOGIC II ( page 24) · Developed by Dolby Laboratories, this surround mode provides 5. 1-channel surround sound with conventional stereo (2-channel) sources. · Select CINEMA mode for movie surround soundtracks, MUSIC for music sources, and GAME for 2-channel game box audio sources. · Canceling MUTING mode: To cancel the muting mode, either press [MUTING] or adjust the volume. Switching the brightness of the display Press DIMMER. Listening over headphones Connect the headphones to <PHONES>. · No sound is produced from the speakers automatically. The brightness of the display can be adjusted in three steps. The display can also be turned off. Using the surround modes NOTE: · To prevent hearing loss, be careful not to raise the volume level excessively when using headphones. Types of surround modes and their features The POA-T3 is equipped with many surround modes. [. . . ] Have you operated the receiver according to the Operating Instructions?If this unit is not operating properly, check the items listed in the table below. Symptom Display not lit and sound not produced when POWER switch set to on. Display lit but sound not produced. Cause Measures (Dolby/DTS Page -- · Surround mode is set to a mode · Set to STANDARD other than STANDARD (Dolby/DTS Surround). [. . . ]