User manual DENON PMA-725R

[. . . ] Follow Instructions ­ All operating and use instructions should be followed. Cleaning ­ Unplug this product from the wall outlet before cleaning. Attachments ­ Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture ­ Do not use this product near water ­ for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. [. . . ] Tuner system buttons Advanced Operation 6, 7 2 1 8, 9 3 0 ~ 9, +10 : : : : : : Manual search (forward and reverse) Stop Play Auto search (to beginning of track) Pause Number 6, 7 2 1 8, 9 3 0 ~ 9, +10 : : : : : : Manual search (forward and reverse) Stop Play Auto search (to beginning of track) Pause Number Default setting = CD The preset codes of a CDR can be recorded in the CD mode so that the CD recorder can be operated ( page 49). It is only possible to set the preset memory for either the CD or CDR. To operate a DENON CDR player, preset "30626" or "31868". To return to operation of a DENON CD player, preset "31867". Default setting = VCR ( page 51) The preset codes of a TAPE can be recorded in the VCR mode so that the tape deck can be operated ( page 49). It is only possible to set the preset memory for either the VCR or TAPE. To operate a DENON TAPE, preset "21471". ·, ª BAND MODE MEMO SRCH SFT CH +, ­ A~G 1~8 SRCH 0~9 : : : : : : : : : : : Tuning up/down Switch between AM, FM and XM bands Switch between AUTO and MANUAL Preset memory Search Switch preset channel range Preset channel up/down Preset channel range Preset channel XM channel direct search XM channel 48 Advanced Operation IR segment Advanced Operation 3 MODE SELECTOR Referring to the included List of Preset Codes ( End of this manual), press the NUMBER to input the preset code (a 5-digit number) for the manufacturer of the component whose signals you want to store in the memory. ·The top IR segment blinks once after each key press. ·If the remote recognizes the manufacturer's code, the IR segment blinks twice. Operating a component stored in the preset memory 1 2 Press the MODE SELECTOR button for the component you want to operate. If it takes longer than that, the remote "times out" and you must begin again. NOTE: · Depending on the model and year of manufacture, this function cannot be used for some models, even if the your device is listed on the included list of preset codes. · Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and check it out. For details, refer to the component's operating instructions. Light setup. · The IR segment blinks twice. 1 2 3 4 5 6 7 Press and hole the SET UP button for at least hold the SETUP three seconds. · The IR segment blinks twice. Press the NUMBER button (1 to 5) you want to adjust the lighting time (5 sec ~ 25 sec). 2 Lighting time 1 2 3 4 5 · The : 5 sec : 10 sec (factory default) : 15 sec : 20 sec : 25 sec IR segment blinks twice as confirmation. 1 2 -1 Press and hold the SETUP button for at least three seconds. · The IR segment blinks twice. Press the 9, 8, 48 button (9 78 4) to select 9, 7, button (9 8) to select a setting. through setting. punch · The IR segment blinks twice. For 1 brightness step increase: Press the CHANNEL + button. Select the MODE SELECTOR button (CD, DVD or VCR) you want to punch through. Repeat step 4. 2 -2 For 1 brightness step decrease: Press the CHANNEL ­ button. Setting the ambient light sensor The included remote control unit (RC-1024) has the ambient light sensor which allows the EL display brightness to automatically adjust depending on how light or dark the amount of incandescent light in the room is. Default state of the ambient light sensor is "OFF" (disable). 3 Press and hold the SETUP button to exit programing. · The IR segment twice as confirmation. Press the MODE SELECTOR button(TV or SAT/CBL) for which you want to set the punch through. Press and hold the SETUP button for at least three seconds. · The IR segment blinks twice. 1 2 3 Press and hole the SET UP button for at least hold the SETUP three seconds. · The IR segment blinks twice. Press the 9, 7, 7, button (9 98) to select a the 9, 9 8 button (97 ). segment blinks twice. · The IR segment blinks twice. Press the ON button. · The IR segment blinks two or four times. Two blinks indicates that ambient light feature was disabled, and is now enabled. Four blinks indicates that ambient light feature was enabled, and is now disabled. 54 Advanced Operation IR segment Advanced Operation 2 Resetting all learned buttons 2 Resetting the punch through setting MODE SELECTOR SYSTEM CALL 1 2 3 NUMBER SETUP Press and hole the SET UP button for at least hold the SETUP three seconds. · The IR segment blinks twice. Press the 9, 7, 7, button (9 68) to select a the 9, 6 8 button (97 ). segment blinks twice. · The IR segment blinks twice. 1 2 3 4 1 2 Press the MODE the SET UP button (TV or SAT / and hole SELECTOR button for at least three you want CBL) seconds. to reset. · The IR segment blinks twice. Press and hold the SETUP button for at least three seconds. · The IR segment blinks twice. Press the MODE SELECTOR button you want to reset twice. · The IR segment blinks twice. Press the 9, 8, 4 button (984) to select a setting. · The IR segment blinks twice. 2 Resetting the system call buttons Press and hold the SETUP button for at least three seconds to reset the punch through setting. · The IR segment blinks twice. 1 2 3 4 Press and hole the SET UP button for at least hold the SETUP three seconds. · The IR segment blinks twice. 2 All reset function Press and hole the SET UP button for at least hold the SETUP three seconds. · The IR segment blinks twice. Press the 9, 7, 7, button (9 88) to select a the 9, 8 8 button (97 ). segment blinks twice. · The IR segment blinks twice. Resetting 2 Resetting the single learned button Press the SYSTEM CALL button (1 to 3) you want to reset. Press and hold the SETUP button for at least three seconds to clear the system call. · The IR segment blinks twice. Press the 9, 8, 7, button (9 18) to select a the 9, 1 8 button (97 ). [. . . ] It is licensed under US and National Patent Applications 20030235318 and 10/700, 220. MultEQ and the Audyssey MultEQ logo are trademarks of Audyssey Laboratories, Inc. . All rights reserved. 93 Additional Information Additional Information Surround modes and parameters Signals and adjustability in the different modes Parameter (default values are shown in parentheses) Dolby Digital FRONT L/R PURE DIRECT, DIRECT DSD DIRECT DSD MULTI DIRECT MULTI CH DIRECT STEREO EXT. IN MULTI CH IN WIDE SCREEN DOLBY PRO LOGICIIx DOLBY PRO LOGICII DTS NEO:6 DOLBY DIGITAL DTS SURROUND 7CH STEREO SUPER STADIUM ROCK ARENA JAZZ CLUB CLASSIC CONCERT MONO MOVIE VIDEO GAME MATRIX VIRTURL C C C C C C C C C C C C C C C C C C C C C C CENTER E E B B E B B B B B B B B B B B B B B B B E SUBSURROUND SURROUND L/R BACK L/R WOOFER E E B B E B B B B B B B B B B B B B B B B E E E B B E B B B B B B B B B B B B B B B B E B B B B B B B B B B B B B B B B B B B B B B D. COMP *1 C (OFF) E E E C (OFF) E E C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) C (OFF) LFE *2 C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) E C (0 dB) C (0 dB) E E E C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) E E E E E E E E E E E C (ON) C (ON) E E E E E E E E E AFDM *1 SB CH OUT (MODE) E E C C E E C C C C C C C C C C C C C C C C TONE CONTROL E E E E C (0 dB) E C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (NOTE1) C (NOTE2) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) C (0 dB) CINEMA EQ. [. . . ]