User manual DENON PMA-2000IVR

[. . . ] INTEGRATED STEREO AMPLIFIER PMA-2000IVR OPERATING INSTRUCTIONS B MUTE/STANDBY VOLUME INPUT SELECTOR TAPE-2/MD TAPE-1/CD-R PHONO CD TUNER DVD/AUX-1 AUX-2/P. DIRECT POWER ¢ ON/STANDBY £ OFF SOURCE DIRECT ¢ ON £ OFF REMOTE SENSOR BASS TREBLE BALANCE REC OUT SELECTOR CD PHONO TUNER AUX-1 AUX-2 AMP POWER MUTING PHONES TAPE-11 2 COPY 9 8 TRACK LEFT RIGHT FUNCTION VOLUME 3 PAUSE 2 STOP CD 1 PLAY B REMOTE CONTROL UNIT RC-858 "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Store the removed short pin-plug in a safe place so as not to lose it. Pre out terminals (PRE OUT) Use these when adding a power amplifier, a subwoofer with built-in power amplifier, etc. Connect these PRE OUT terminals to the input terminals on the additional power amplifier, subwoofer, etc. NOTE: Signals are outputted from the PRE OUT terminals even when using headphones. No signal is outputted when selecting power amp direct terminal (see o, page 5) !3 Playing and recording input/output terminals (TAPE-1/CD-R, TAPE-2/MD) These are playing and recording input/output terminals for connection to tape decks. !7 !8 Speaker systems terminals (SPEAKER SYSTEMS) Connect the speaker systems here. !4 Power amp direct terminals (POWER AMP DIRECT) Souurce connected to this terminal is directly fed to the power amp. set volume level by the component connected to this terminal. AC inlet receptacle (AC IN) Connect the included power supply cord here. Do not use any other cord than the provided power supply cord. !5 !9 Attachment plug receptacles (AC OUTLETS) AC outlets are used for connecting amplifier component units, such as tuner, turntable, tape deck, etc. · SWITCHED (Total capacity: 120 W / 1 A): These outlets are turned ON/OFF when main power switch is turned on/off. · UNSWITCHED (Capacity: 240 W / 2 A): This outlet is always ON whether power switch is on or off. NOTE: This equippment may be different according to the country. Power amp direct switch (POWER AMP DIRECT) ON position: Power amp direct terminal is selected when INPUT SELECTOR is set to AUX-2/P. DIRECT position. 6 @0 Ground terminal (SIGNAL GND) Connect the turntable's ground wire here. NOTE: This terminal is used to reduce noise when a turntable, etc. , is connected. It does not provide grounding. @1 Cartridge selection switch (CARTRIDGE) This switch is set according to the type of player cartridge to be used. Set this switch to MM (£) or MC (¢) according to the type of cartridge used on your turntable. 2 CONNECTIONS Connecting the speakers · Speaker impedance · When using speaker systems A and B separately, speakers with an impedance of 4 to 16 /ohms can be connected. · When biwiring with biwireable speaker system, speakers with an impedance of 4 to 16 /ohms can be connected. · Note that when using two sets of speaker systems together (A + B), use speakers with impedance 8 to 16 /ohms, using speakers with an impedance other than between 8 to 16 /ohms may cause damages. Note that this unit is not equipped with a switch for selecting the speaker system. · The protective circuit may be activated if speakers with other impedances are connected. · Be sure to connect the cords between the speaker terminals and speaker systems with the same polarities (< to <, > to >). If not, the central sound will be weak and the position of the different instruments will not be clear, diminishing the stereo effect. · When connecting the speakers, be sure that the core wires of the speaker cords do not stick out from the terminals and touch other terminals, each other or the rear panel. · Connecting the speaker cords q Peel off the sheathing from the end of the cord. r Insert the core wires entirely, then turn the terminal clockwise to tighten it. CAUTION Protective Circuit This set is equipped with a high speed protective circuit. [. . . ] VOLUME ª DOWN : While this is pressed, the main unit's volume control turns counterclockwise and the volume decreases. FUNCTION · : Use this to select the program source to be played. The function switches in the following order each time this is pressed: CD / TUNER / DVD/AUX-1 / AUX-2/ P. DIRECT / TAPE-2/MD / TAPE-1/CD-R / PHONO / CD FUNCTION ª : Use this to select the program source to be played. [. . . ]