User manual DENON DRR-M33

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Se till att det finns möjlighet till god värmeavledning vid montering i ett rack. € DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. [. . . ] œ When connecting to the RCD-M33/M35DAB, connect to the TAPE OUT terminals on the CD receiver (RCD-M33/M35DAB). € When using with the RCD-M33/M35DAB, connect this connector to the system connector on another unit using the included system connector cable. Side A Cleaning the Heads Cautions on Storing Cassette Tapes • Do not place cassette tapes in the following places: 1. ) • Store cassette tapes in cases with stoppers to prevent the tape from becoming slack. A commercially available head cleaning cassette (wet type) is required to clean the heads (recording/ playback and erasing) on this product. € If the heads are dirty, sound cannot be recorded or played with good quality. € To take full advantage of this product’s performance and to achieve good sound quality, clean the heads periodically after approximately 10 hours of use. € We recommend using a wet type commercially available head cleaning cassette that also cleans the pinch roller and capstan. 7 LINE IN (analog input) terminals Degaussing the Heads • The heads become magnetized after extended use or after being exposed to magnetized objects. € Use a commercially available cassette type head degausser to demagnetize the heads. NOTE: • Set the amplifier’s volume to the minimum when cleaning and degaussing the heads. High tape (TYPE II) A The DRR-M33 is equipped with an auto tape selector mechanism which uses the detection holes in the cassette halves to detect the type of tape and automatically set the most appropriate recording bias and equalization for that type of tape. Detection holes Reverse A (2) Auto Tape Select Mechanism A A A NOTES: • If a foreign object is caught in the cassette tray during closing, simply press the 5 (open/close) button again and the tray will open. 6 8:50 ページ 8 ENGLISH 8 PLAYBACK (1) Starting Playback 2 2, 3 7 (2) Stopping Playback 1 (3) Fast-forwarding and Rewinding z To fast-forward the tape 1 x To rewind the tape 1 1 5 6 4 2 2 1 Turn on the power. NOTE: • Be sure to press the 2 (stop) button to stop playback before turning off the power or unplugging the power supply cord. 6 Press the 0 1 (direction) button to change the direction of playback. 6 8:50 ページ 9 ENGLISH (4) Using the Music Search Function Example 1: Finding the beginning of the 4th selection on front side while playing the 1st selection. Example 2: Finding the beginning of the 2nd selection on front side while playing the 4th selection. 1 Blank space 1st selection Blank space Blank space 4th selection Playback starts Blank space 1st selection Blank space Blank space 4th selection Load the cassette tape onto which you want to record. 2nd selection 3rd selection 2nd selection 3rd selection 2 Music search operation Music search operation 1 Press three times. NOTE: • Be sure to press the 2 (stop) button to stop recording before turning off the power or unplugging the power supply cord. € The music search function detects and counts the blank (non-recorded) spaces between selections. [. . . ] € When the editing function is used for recording, set the REVERSE MODE switch to if not, it is not possible to record on side B after side A. € In some cases it may not be possible to record all the tracks on the disc, even if the tape is longer than the disc’s recorded time (because of how the tracks are divided onto sides A and B of the tape). The “OVER” indicator on the CD receiver flashes if there are tracks that cannot be recorded. € REC button, 6 7 button, CD SRS button, 0 1 (direction) button and 5 (open/close) button will not function during editing. [. . . ]