User manual DENON DRA-397

[. . . ] AM-FM STEREO RECEIVER DRA-397 OPERATING INSTRUCTIONS ENGLISH ¢SAFETY PRECAUTIONS SAFETY INSTRUCTIONS Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. [. . . ] Never use it for hair driers, monitors or other electrical appliances. G Monitor Monitor (ZONE2 or ZONE3) (ZONE2) VIDEO IN A L R Power amplifier Power amplifier (ZONE2 or ZONE3) (ZONE2 or ZONE3) L R L IN R · For the AUDIO output, use high quality pin-plug cables and wire in such a way that there is no humming or noise. · For instructions on installation and operation of separately sold devices, refer to the devices' operating instructions. 10 ENGLISH ENGLISH FUNCTION <PRESET ·> STATUS <SELECT> <SPEAKER> <TONE DEFEAT> VOLUME Operation Before operating Turning the sound off temporarily (MUTING) Press [MUTING]. 1 Press <POWER>. ¢ ON: The power indicator lights red. <LOUDNESS> <POWER> <CH VOL> PURE DIRECT <ON/STANDBY> <PHONES> <TONE CONTROL> £ OFF: The power turns off and the indicator is off. · Canceling MUTING mode: To cancel the muting mode, either press [MUTING] or adjust the volume. [POWER ON] FUNCTION 2 Set [MODE SELECTOR 1] to "A". 4 Press <ON/STANDBY> or [POWER ON]. Playing the input source Listening over headphones Connect the headphones to <PHONES>. · No sound is produced from the speakers automatically. · The power indicator blinks green and the power turns on. NOTE: · To prevent hearing loss, be careful not to raise the volume level excessively when using headphones. VOLUME [MUTING] [DIMMER] STATUS PURE DIRECT [MODE SELECTOR 1] [VIDEO SELECT] [MODE SELECTOR 2] 1 Use FUNCTION to select the input source you want to play. 2 Start playback on the selected component. For operating instructions, refer to the component's manual. Switching the speakers Press <SPEAKER> to turn the corresponding speaker pair on. 3 Use VOLUME to adjust the volume. FUNCTION · The volume level is displayed on the volume level display. About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit 11 ENGLISH ENGLISH Operation Operation Checking the currently playing program source, etc. Press STATUS. · The current program source and various settings are indicated on the display. ¢ When you do not want to adjust the tone Press <TONE DEFEAT> to select "TONE DEFEAT ON". ¢ When listening with the volume turned low Press <LOUDNESS> to select "LOUDNESS ON". Listening to the radio Check that the remote control unit is set to "A". Auto preset memory This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory. Switching the brightness of the display Press [DIMMER]. The brightness of the display can be adjusted in three steps. The display can also be turned off. ON/STANDBY 1 Press <standby mode. > and set the DRA-397's power to the Adjusting the speaker volume 1 Press <CH VOL> to select the speaker. The settable speaker switches each time this button is pressed. 2 Hold <PRESET ·> and press <ON/STANDBY>. · The unit automatically begins searching for FM broadcast stations. Selecting the play mode (PURE DIRECT) This mode reproduces the sound with extremely high quality. The display that could affect the audio signals are turned "OFF". 2 Use <SELECT> to adjust the volume. Can be adjusted within the range of ­12 dB to +12 dB. When the first FM broadcast station is found, that station is stored in the preset memory at channel A1. Subsequent stations are automatically stored in order at preset channels A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1 to E8, F1 to F8 and G1 to G8 for a maximum of 56 stations. Channel A1 is tuned in after the auto preset memory operation is completed. Press PURE DIRECT. Combining the currently playing sound with the desired image (VIDEO SELECT function) Press [VIDEO SELECT] until the desired image appears on the display. · If an FM station cannot be preset automatically due to poor reception, use the "Manual tuning" operation to tune in the station, then preset it using the manual "Preset memory" operation. · To interrupt this function, press <ON/STANDBY>. Setting the tone control ¢ Adjusting the tone Press <TONE 1 "TREBLE". CONTROL> to select "BASS" or · To cancel, press [VIDEO SELECT] to select "SOURCE". · The video source selected with the video select function is stored in the memory for the different input sources. ¢ Default settings Auto tuner presets 87. 5 / 89. 1 / 98. 1 / 107. 9 / 90. 1 / 90. 1 / 90. 1 / 90. 1 MHz 520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90. 1 / 90. 1 MHz 90. 1 MHz 90. 1 MHz 90. 1 MHz 90. 1 MHz 90. 1 MHz 2 Use <SELECT> to set the level. Can be adjusted within the range of ­10 dB to +10 dB. A1 ~ A8 B1 ~ B8 C1 D1 E1 F1 G1 ~ ~ ~ ~ ~ C8 D8 E8 F8 G8 12 ENGLISH ENGLISH Operation Operation FUNCTION MODE BAND SHIFT Auto tuning STATUS Preset memory XM RADIO TUNING MEMORY <PRESET> "Auto tuning" 1 Use FUNCTION to select "TUNER" or press [TUNER]. 1 Use the in the station toor "Manualintuning" operation to tune be preset the memory. · Automatic searching begins. SHIFT [FM/AM] [CHANNEL] XM RADIO FUNCTION · If tuning does not stop at the desired station, use to the "Manual tuning" operation. · "AM" or "FM" can be selected directly by pressing [FM/AM]. 5 Press MEMORY again. · Store the station in the preset memory. [D H F G] STATUS Manual tuning · To preset other channels, repeat steps 2 to 4. A total of 56 broadcast stations can be preset -- 8 stations (channels 1 to 8) in each of blocks A to G. [NUMBER] (0 ~ 9, +10) BAND [MEMORY BLOCK] FUNCTION MODE MEMORY [TUNER] TUNING 1 Use FUNCTION to select "TUNER" or press [TUNER]. Recalling preset stations Press BAND to select "AM" or "FM". (A to G) or SHIFT to select 3 Press MODE to set the manual tuning mode. Press <PRESET>, 2 the desired preset [CHANNEL] or [NUMBER] to select channel. 4 Check that the display's "AUTO" indicator turns off. [. . . ] Have you operated the receiver according to the Operating Instructions?If this unit is not operating properly, check the items listed in the table below. Symptom Display not lit and sound not produced when POWER switch set to on. Display lit but sound not produced. Cause · Batteries dead. [. . . ]