User manual DENON DN-X1700

[. . . ] Professional DIGITAL DJ Mixer DN-X1700 Owner's Manual n SAFETY PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN FCC INFORMATION (For US customers) 1. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product. [. . . ] BACK (EFX 2 side only): This is used when returning to the previous screen while setting screen operations are being performed. Fader Start t MIDI CLOCK START/STOP button This enables the MIDI clock corresponding to the BPM value to be sent from the USB MIDI and MIDI output terminals to the computer (software) or external device. STOP: Sending the MIDI clock is stopped. W7 W6 W5 W4 W3 W2 W1 W0 Q9 Q8 USB Utility Q0 Effect CUE button When this button is set to ON, the sound of the effects (but not the DELAY, ECHO or REVERB effects) can be monitored even if the effect OFF status. Specifications y UTILITY/­USB A/USB B button This allows the presets to be set and the system information to be set, changed or referenced. When it is held down for more than a second, the USB mode switching screen is opened, and the USB device mode or USB host mode can be selected. Q1 EFX SELECT control This is for selecting the effect to be used. Refer to the effect functions (page 9). Troubleshooting Q2 Parameter ON/OFF button This is used to control the ON and OFF settings of the effect parameters. u BEAT , buttons (Short) : The beat/time is decreased. (Long) : The beat/time is increased. Q3 PARAMETER MIX/MAX control This is used to adjust the filter cutoff frequency and other effector parameters. The parameters are changed by the effector selected. R0 Q7 Q6 E9 Q4 DRY/WET control Use this to adjust the ratio of original and effected sound. 3 Q5 Effect ON/OFF button This sets the effects of EFX 1 or EFX 2 to ON or OFF. W6 MIC SEND LEVEL control This is used to adjust the level at which the mic signals are sent to the master output. E4 MIDI layer selector buttons When these buttons are set to ON, the controls of the selected channels function as MIDI controllers. Also, the EQ control rings light up blue. R2 L/CUE, R/PGM master level meter One of two modes can be selected for display on this meter. Split CUE ON: The right channel master CUE (monaural) and left channel CUE (monaural) audio levels are displayed. Getting Started Connections Basic Operations Getting Started Effector Function Fader Start USB Utility Specifications Troubleshooting Q6 CROSSFADER Controls the relative output level from the summed A and B Mixes. When the fader is at its far left, only the A Mix is heard from the Outputs. As the fader is moved toward the right, the amount of B Mix is increased and the amount of A Mix is decreased. When the fader is centered, equal amounts of A and B Mixes are routed to the Outputs. Fully right is all B Mix at the Outputs. W7 Mic EFX INS 1, 2 buttons These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the mic input signals. E5 Channel input LEVEL controls These are used to adjust the levels of the selected inputs. W8 MIC EQ controls Contour the frequency response of the Mic input ­15 dB to +15 dB. E6 Channel isolator EQ controls (HI, MID, LOW) These are used to change the frequency response of the selected inputs. At the ­ position, the frequencies of all the bands are cut off completely. W9 DUCKING ON/OFF button ·UsethistoswitchtheTalkOverfunctionONand OFF (ON/OFF is cyclic) . ·When the button is lit, level of signals except Mics is attenuated. * The ducking attenuation level can be adjusted in the "UTILITY" mode. R3 SIG/PK This is the signal/peak meter for the mic input level. Off: No signals input (under ­60 dB/FS) Green: Signal input (­60 dB/FS to under ­20 dB/FS) Orange: Suitable signal input level (­20 dB/FS to under ­6 dB/FS) Red: Excessively high signal input level (above ­6 dB/ FS) Q7 Channel input fader (CH FADER) Controls the level of the selected Input. Q8 HEADPHONE output jack Accepts 1/4" stereo headphone plugs. E7 CH LEVEL meter Displays the input level after adjusted with LEVEL E5 and Source EQ E6 controls. Q9 HEADPHONE level control Adjusts the volume for the headphones. E0 MIC1, MIC2 TRIM controls Adjusts the level of the Main Mic input. W0 HEADPHONE PAN control This is used to adjust the balance between the CUE sound and the master sound which are monitored using the headphones. E1 MIC1, 2 buttons When the button's LED is lighted, the mic signals take effect. E2 CD/PHONO line input selector buttons These enable the line input of each channel to be selected as CD or PHONO. CD: Rear panel LINE1­4 CD terminal input PHONO: Rear panel LINE1­4 PHONO terminal input W1 SPLIT CUE button There are two headphone monitor modes. Stereo mode (SPLIT CUE OFF): The cue signals and master signals can be monitored in stereo. SPLIT CUE mode: The monaural cue signals are heard through the left channel of the headphones, and the monaural master signals through the right channel. E8 Channel EFX SEND 1, 2 buttons These buttons enable the various effects of the selected side, either EFX 1 or EFX 2, to be obtained for the channel audio signals. The same effect (EFX 1 or 2) can be selected for a multiple number of channels. The LED of the EFX button for the side selected for each channel lights. E9 Channel CUE buttons Pressing in any or all of CUE buttons routes the respective source to the headphone and meter cue sections. [. . . ] whether the preset memory is to updated selected, the preset 3 When OK isupdated to the contents of the export memory are the contents of files. * If the export file already exists, a screen prompting the user to verify whether the file is to be overwritten appears. Preset Recall * Bear in mind that the data prior to the updating will not be retained. *1: Using the Preset stored externally, the internal memory is updated, and the settings are reflected in the device. *2: All the Owner settings and Preset are set to the factory settings. USB memory device with the export files 1 Insert the already inserted. on the unit's power with into the DN-X1700 or turn the device 2 A screen prompting the user to verify whether the presets are to be called appears. OK is selected, preset Setting and 3 When information the theinsidefileAudiocalled. [. . . ]