User manual DENON DN-HC4500

[. . . ] USB MIDI / AUDIO INTERFACE & CONTROLLER DN-HC4500 OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG MODE D'EMPLOI INSTRUCCIONES DE FUNCIONAMIENTO CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. [. . . ] For instructions on operating the DN-D4000/ D4500/BU4500, refer to the respective model's operating instructions. t AC Inlet terminal · Inlet the power cord's plug into DN-HC4500's AC inlet terminal. [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · TIME: When this button is pressed, the time indicator switches between "ELAPSED" (elapsed time), "REMAIN" (remaining time). · Total: When this button is pushed for more 1 second, you can display the total time. [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · MEMO: The MEMO mode starts when this button is pushed once in the Cue/Pause mode. · PRESET: When this button is pushed for more than 1 sec, the PRESET mode menu is displayed. y Fader start terminals · Use this when your mixer has the Fader Start function. e USB B terminal · Connect to a computer. · Sends the USB audio signals from a PC. u X-CONROL output terminal · Use this when connected to a DENON DNX900 or DN-X500 mixer that offers X-Control. · With the DN-HC4500 it is possible to convert the input fader position into a MIDI signal and send it from the USB terminal. o FLIP/B TRIM [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Push this button to switch between the loop mode/hot start mode and stutter mode. · After setting the B point, the B TRIM MODE can be selected. !1 CUE/STUTTER [When PCDJ connected], [When DN-D4500 connected] · Pushing this button in play mode will force the file back to the position which playback started. · In Cue mode, by pushing the CUE button makes a Stutter sound from the Cue point. (Stutter) 3 ENGLISH ENGLISH !2 TITLE [When PCDJ connected] Refer to the PCDJ's manual. · MP3: The ID3 tag information switches each time the button is pressed. !8 EXIT/RELOOP [When PCDJ connected], [When DN-D4500 connected] · Use this to exit or return back again to Seamless loop playback. You can add variety to looping with this function. @4 PITCH BEND± [When PCDJ connected], [When DN-D4500 connected] · While pushing these buttons will change main playing speed temporarily. · When release button, playing speed returns to the previous speed. #1 EFFECT1 [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Turns the Brake mode ON or OFF. #2 FAST SEARCH (6/7) QUICK JUMP [When PCDJ connected], [When DN-D4500 connected] · QUICK JUMP: When one of these buttons is tapped shortly, the playback position jumps in the reverse (6) or forward (7) direction. · FAST SEARCH: When one of these buttons is pressed and held in, the disc is fast-searched in the reverse (6) or forward (7) direction. !9 JOG MODE [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] Select from Bend mode or Manual Frame Search mode. @5 PLAY LIST [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Push this butoon to open and close the disc holder. Stop playback before pushing this button. !3 A1, A2 [When PCDJ connected], [When DN-D4500 connected] · Using this button you can create starting point for Hot Start, Seamless Loop and Stutter. @0 JOG indicator [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · This vibrant blue bar provides JOG modes at a glance such as, Pitch Bend and Frame Search. !4 CONT. /SINGLE, RELAY @6 TAP [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · Does not function. [When PCDJ connected] Refer to the PCDJ's manual. [When DN-D4500 connected] · CONT. /SINGLE: A short tap of this button will toggle between 3 possible END modes for playback CONT. [. . . ] The following is displayed on the device's panel during version updating: On Deck1: "Version up was not completed. " When version updating was not completed normally. Once version updating is completed: If version updating has failed, "Version up was not completed. " is displayed and the screen returns to as it was before the Execute button was pressed. Press the Execute button again. 13 ENGLISH ENGLISH 11 MIDI COMMANDS Data transmission The panel operation data is transmitted by MIDI command, as per the table below. mode MIDI command Command SW ON : 0x9n SW OFF : 0x8n Number 0x52 0x53 Value SW ON : 0x40 SW OFF : 0x00 Reverse 0x3F ~ 0x00 Foward 0x41 ~ 0x7F slow fast relative data 0x00 (min) 0x7F (max) Increment : 0x00 Decrement : 0x7F 0xmmh (MSB) Message type Note ON/OFF 38 Jogwheel fwd/rev items 1 2 3 4 5 6 7 8 9 Playlist JOG mode Pitch/KEY TAP Pitch Bend+ Pitch Bend­ Fast search+ Fast search­ EFX1/ECHO/LOOP MIDI command Command SW ON : 0x9n SW OFF : 0x8n Number 0x02 0x04 0x05 0x07 0x08 0x09 0x10 0x11 0x12 0x13 0x14 0x17 0x18 0x19 0x20 0x21 0x23 0x24 0x25 0x26 0x28 0x30 0x31 0x36 0x37 0x38 0x39 0x40 0x42 0x43 0x47 0x48 0x49 0x50 0x51 Value SW ON : 0x40 SW OFF : 0x00 Message type 39 X-Control fader Note ON/OFF Parameters KNOB 40 Increment/Decrement 41 Pitch Slider 0xBn 0x51 Control change 0xEn 0x53 0x54 0xllh (LSB) Pitch bend change ­100% : 0x7F7F (MSB/LSB) 0% : 0x4000 (MSB/LSB) +100% : 0x0000 (MSB/LSB) n = MIDI CH 10 EFX2/FLANGER 11 EFX3/FILTER 12 HOT1 13 HOT2 14 HOT3 15 HOT4 16 HOT5 17 TIME/TOTAL 18 MEMO/PRESET 19 TITLE 20 CONT. /SINGLE 21 Parameters KNOB SW 22 BACK 23 SOURCE mode 24 FLIP 25 A1 26 A2 27 B 28 EXIT/Reloop 29 Cue 30 Play 31 JOG UP 32 JOG DOWN 33 JOG LEFT 34 JOG RIGHT 35 Jogwheel touch 14 ENGLISH ENGLISH VFD symbol data reception The various VFD symbols can be set to on, off or blinking, as per the table below. 2 Receive command for VFD Symbol items MIDI command Command 0xBn Number ON TRG : 0x4A OFF TRG : 0x4B Blink ON TRG : 0x4C Value 0x02 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1E 0x24 0x3C 0x25 0x3D 0x26 0x27 0x3B only Use 0x4A (request TRG) only Use 0x4A (request TRG) 0x3C 0x3D DN-HC4500 return pitch slider position DN-HC4500 return XControl fader position Message type Notes MIDI command Command 0xBn Number ON TRG : 0x4D OFF TRG : 0x4E Blink ON TRG : 0x4F Value 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x10 0x11 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 only Use 0x4F/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E only Use 0x4D/0x4E 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 Message type Data reception LED data reception The panel's LEDs can be set to on, off or blinking by MIDI command, as per the table below. [. . . ]