User manual DENON DN-F450R

[. . . ] SOLID STATE RECORDER DN-F450R Owner's Manual PORTUGUS SVENSKA NEDERLANDS ESPAOL ITALIANO FRANAIS DEUTSCH ENGLISH IMPORTANT TO SAFETY WARNING: CAUTION 1. Handle the power supply cord carefully Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord. [. . . ] To return to the upper level menu from the menu item currently being set, press and hold the jog dial. The changed settings are saved, and the DN-F450R returns to the stopped status. Rotate the jog dial to select the setting item that you want to change, and press the jog dial. File/Folder Control function settings 4 Select the setting item that you want to change, and press the jog dial. 5 After you finish all settings, press DISPLAY. To cancel the settings, press the STOP button before saving the settings. When you perform recording by setting the audio input source to "Bal", be sure to set the FS switch on the rear panel to the maximum input level (+24dBu or 0dBu) before you start recording. 02 Rec Format MP3-320 / MP3-256 / MP3-192 / MP3-128 / MP3-64 / Selects the audio format PCM-16 (MP3 or PCM) for recording. frequency for recording. Information Specifications Index 11 Setting defaults Setting Items LevelCont Selects the adjustment method for the recording level. Level LED Sets the input/output level for the Level display lit on the main unit. Setting details Manual : The recording level can be adjusted to the desired value. Setting Items Skip Back Sets the amount of time used for skipping back a track. Setting details 0. 5 sec 10 sec: Sets the time by increments of 0. 5 seconds. 10 sec 60 sec: Sets the time by increments of 5 seconds. -6dB / -12dB / -20dB / -38dB / -54dB Auto Track Creates a new file for each recording time set and continues recording. You can use this setting for various purposes besides the level meter on the display. For example, confirmation of the recording peak level and confirmation of the presence or absence of input signals. 1 min/ 5 mins/ 10 mins/ 15 mins/ 30 mins/ 1 hour/ 2 hours/ 6 hours/ 8 hours/ 12 hours/ 24 hours Play Mode Selects the play mode. NOTE If the size of the recorded file exceeds 4GB, recording is continued on a new file irrespective of the set time. There could be sound cutoffs for a short period of time between files depending on the capacity of a recorded file. FinishMod (Finish Mode) Sets the stop status when playback is stopped. Repeat Sets the file to repeat playback. The skip back function rewinds a track for the set amount of time from the current playback position during playback or pause. This function is useful when you perform remote control functions using the Remote 2 expanded function switches. For details on the remote control, see "Expanding remote functions" (vpage 27). Single: When the file has finished playing, it is stopped in the stop position set in "Finish Mode". Next: When the STOP button is pressed during file playback, playback is stopped at the head of the next file. Recue: When the STOP button is pressed during file playback, playback is stopped at point where playback was previously started. On: Repeat playback is performed. Auto Mark When input lower than the input level set in "10 Silent Level" continues for more than 3 seconds, marking information is written into the file. This mark is useful when searching for a specific point during playback. [. . . ] Contact your local Denon repair service center listed on our website (URL: http://www. d-mpro. com). Page 23 20 25 9 24 Full Media Full 999 Full MARK Full Folder 14 No Files No MARK ALC VBR 20 Need Update 40 Troubleshooting If a problem should arise, first check the following: 1. If this unit does not operate properly, check the items listed in the table below. If the symptom is not covered on the check list, contact your dealer or service centers. [. . . ]