User manual DENON DN-A7100

[. . . ] AV SURROUND PREAMPLIFIER DN-A7100 USER GUIDE BEDIENUNGSANLEITUNG MODE D'EMPLOI GUIDA DELL'UTENTE GUÍA DEL USUARIO GEBRUIKSAANWIJZING GUIA DO UTILIZADOR BRUKSANVISNING ENGLISH WARRANTY For warranty information, contact your local DENON distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with DENON. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] Note: LFE signals during playback of Dolby Digital or DTS, will be played through the sub woofer. Use this parameter to specify the distance of each speaker's position from the listening position. The delay time is automatically calculated according to these distances. Begin by determining the ideal or most commonly used seating position in the room. This is important for the timing of the acoustics to create the proper sound space that the DN-A7100 and today's sound systems are able to produce. Note: For speakers that you have selected "NONE" the Speaker Configuration sub-menu will not appear here. (There are several useful books and special DVD and LD's available to guide you through proper home theater configuration. If you are unsure, have your DENON dealer perform the installation for you. They are trained professionals familiar with even the most sophisticated custom installations. DENON recommends the WWW. CEDIA. ORG website for further information about this). 2-2 SPEAKERS DISTANCE FRONT L : 10 FRONT R : 10 CENTER : 10 SURR. L : 10 SURR. R : 10 SUB W : 10 SURR. B L : 10 SURR. B R : 10 MAIN RETURN ft ft ft ft ft ft ft ft 3. 0 m 3. 0 m 3. 0 m 3. 0 m 3. 0 m 3. 0 m 3. 0 m 3. 0 m EXIT If you select "MANUAL", adjust the output level of each speaker as listed below. 1. When you move the cursor to FRONT L by pressing the 4 cursor button, the DN-A7100 will emit a pink noise from the front left speaker. (Note that this can be adjusted to any level between -10 and +10 dB in 1 dB intervals except the subwoofer setting. The subwoofer can be adjusted to any level between -15 and +10 dB in 1 dB intervals. ) The DN-A7100 will now emit the pink noise from the center speaker. Notes: · Set the distance to each speaker in meters (m) or feet (ft) as follows. m: 0. 3 - 9 m in 0. 3 m steps ft: 1 - 30 ft in 1 ft steps · For the speakers that you have selected "NONE" the Speaker Size menu will not appear. · The setting for Surr. Back L and Surr. Back R appears if you set for it to, two surround back speakers in the Speaker Size menu. · The setting of Surr. Back appears if it is set for one surround back speaker in the Speaker Size menu. 2. Using the 1 and 2 cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker. The DNA7100 will now emit the pink noise from the front right speaker. Repeat steps 2 and 3 above for the front right and other speakers until all speakers are adjusted to the same volume level. 1. To set the distance for each speaker , press the 1 or 2 cursor buttons. After you complete this portion of the set up, move the cursor to "NEXT" with the 3 or 4 cursor buttons and then press the ENTER button to go to the next page. 2-3. SPEAKERS LEVEL SETTING WITH TEST TONE Here you will set the volume for each speaker so that they are all heard by the listener at the same level. We recommend using a SPL (Sound Pressure Level) meter, when available. Note: The speaker level settings are not available in 7. 1 Channel Input mode, CS mode and Multi Channel Stereo mode. 2-3 SPEAKERS TEST MODE FRONT L CENTER FRONT R SURR. R SURR. B R SURR. B L SURR. L SUB W MAIN RETURN LEVEL : MANUAL : 0 dB : 0 dB : 0 dB : 0 dB : 0 dB : 0 dB : 0 dB : 0 dB EXIT 3. 4. FRONT L: Set the distance from the front left speaker to your normal listening position. [. . . ] 87. 5 ­ 108. 0 MHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . IHF 1. 8 µV/16. 4 dBf Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . Mono/Stereo 75/70 dB Distortion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono/Stereo 0. 2/0. 3 % Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 kHz 45 dB Alternate Channel Selectivity . . . . . . . . . . . . . . . . . ± 300 kHz 60 dB Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 MHz 70 dB Tuner Output Level . . . . . . . . . . . 1 kHz, ± 75 kHz Dev 800 mV Memory backup · In case a power outage occurs or the power cord is accidentally unplugged, the DNA7100 is equipped with a backup function to prevent memory data such as the preset memory from being erased. AM TUNER SECTION Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 ­ 1602 kHz Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]