User manual DENON DHT-M330DV

[. . . ] HOME THEATER SYSTEM DHT-M330DV OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG MODE D'EMPLOI ISTRUZIONI PER L'USO INSTRUCCIONES DE OPERACION GEBRUIKSAANWIJZING BRUKSANVISNING AVR-M330 DVD-M330 SYS-M330 (SC-AM330) · DVD-M330(DVD PLAYER): · DVD-M330 (DVD-PLAYER): · DVD-M330 (LECTEUR DVD): · DVD-M330 (LETTORE DVD): · DVD-M330 (REPRODUCTOR DVD): · DVD-M330 (DVD-SPELER): · DVD-M330 (DVD-SPELARE): FOR ENGLISH READERS FÜR DEUTSCHE LESER POUR LES LECTEURS FRANCAIS PER IL LETTORE ITALIANO PARA LECTORES DE ESPAÑOL VOOR NEDERLANDSTALIGE LEZERS FOR SVENSKA LÄSARE (SC-CM330) DSW-M330) (SC-AM330) Please refer to the operating Instructions of the DVD-M330. Veuillez vous référer au mode d'emploi du DVD-M330. PAGE SEITE PAGE PAGINA PAGINA PAGINA SIDA 004 058 112 166 220 274 328 ~ ~ ~ ~ ~ ~ ~ PAGE SEITE PAGE PAGINA PAGINA PAGINA SIDA 057 111 165 219 273 327 381 ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] · The tone switches as follows each time the SDB/P. EQ button is pressed. VOCAL ENH · The VOCAL ENHANCER is turned on. · When listening quietly at night, the vocals are easier to hear. · The surround channel is emphasized for a stronger sense of presence. When SDB/P. EQ is turned on, SURROUND ENHANCER is set to "ENHANCER OFF". [3] Turning the sound off temporarily (MUTING) Main unit Remote control unit SDB ON DEFEAT ( DRC ON ) P. EQ1 P. EQ2 P. EQ3 DEFEAT · The signals do not pass through the SDB, DRC and P. EQ1~3 adjustment circuits, providing higher quality sound. · This parameter adjusts the dynamic range of the Dolby Digital or DTS sound. When listening with the volume turned relatively low, at night for example, set this to the "ON" to lower the peak of the sound and amplify the quieter sounds, narrowing the dynamic range and making the sound easier to listen to. · With DTS source, only displayed for sources compatible with dynamic range compression. P. EQ1~3 · Preset Equalizer is turned on · Three types of bass/treble balances and surround channel delay settings are preset. If no operation is performed within 4 seconds, the display switches back to what was previously displayed. 1 1 Use this to turn off the audio output temporarily. Press the MUTING button again. Remote control unit NOTES: · The mute mode is cancelled when the main unit's main volume control or one of the main volume control buttons on the remote control unit is operated. · The setting is cancelled if the set's power is turned off. 32 ENGLISH 10 SURROUND PLAYBACK (1) Before playing with the surround function · Adjustments using the test tones can only be performed in the "Auto" mode and are only valid for the AUTO DECODE Surround modes. · Even after adjusting using the test tones, the various channels can be adjusted using the procedure described below to suit the program source and your preferences. 1, 4 2 2, 4 1, 3 4 3 3 1 Press the TEST TONE button. 1 Remote control unit Press the CH. SELECT button on the remote control unit. · The following is displayed: L E VE L < / >D ELAY Remote control unit 2 Test tones are output from the different speakers. Either turn the MASTER VOLUME dial on the main unit or use the VOLUME buttons on the remote control unit to adjust the volume. 2 Use the select button while the above is displayed to select "LEVEL". · The level display shown below appears. + Main unit Remote control unit FL VOL< 0 dB> Remote control unit 3 3 Use the channel volume adjust buttons to adjust so that the volume of the test tones is the same for all the speakers. · The ( and ) cursor buttons on the remote control unit during the adjustments using the test tones. Select the speaker whose level you want to adjust. · The channel switches as shown below each time the button is pressed. END SUBWOOFER FRONT L CENTER FRONT R SURROUND L SURROUND R Remote control unit Remote control unit 4 After adjusting using the test tones, adjust the channel levels either according to the playback sources or to suit your tastes, as described below. 4 Adjust the volume level of the selected speaker while the channel level is displayed. Remote control unit Remote control unit Once the channel level setting is completed, select "END" at step 3. The display returns to normal after several seconds. 33 ENGLISH (2) Playing in the AUTO DECODE mode · In the auto decode mode it is possible to play in the Dolby Digital or DTS Surround mode, depending on the format of the input signal. · It is also possible to play in the Auto Stereo, Dolby Pro-Logic II Cinema/Music/Game or DTS NEO:6 Cinema/Music mode, according to the 2channel mode setting. [1] Dolby Digital and DTS surround playback (digital inputs only) · Applicable sources · Digital inputs (DVD, TV/AUX1 and AUX2 functions) Dolby Digital multi-channel sources DTS sources 3 Set the surround mode to "AUTO DECODE". or 1 Main unit Remote control unit If the mode is set to anything other than AUTO DECODE, the AUTO DECODE mode can be set using the AUTO DECODE button on the remote control unit. 3 · Operate the remote control unit at the "AMP" position. 4 Play a program source containing the mark. · The Dolby Digital indicator lights when playing a Dolby Digital source. [. . . ] After several seconds, "INITIALIZE" appears on the display and the power turns on. · The microprocessor is initialized. 1 22 NOTES: · If step 3 does not work, start over from step 1. · If the microprocessor is reset, all the buttons and the setup settings are reset to the factory default values. 55 ENGLISH 18 TROUBLESHOOTING Check again before assuming the player is malfunctioning 2 Are all the connections correct ?2 Are the speakers and other components operating properly ? If this unit does not seem to be functioning properly, check the table below. [. . . ]