User manual DENON AVR-985S

[. . . ] AV SURROUND RECEIVER AVR-2805/985 OPERATING INSTRUCTIONS MASTER VOLUME FUNCTION SOURCE TUNING PRESET ZONE 2 / REC SELECT VIDEO SELECT ON / STANDBY MODE ANALOG EXT. 2 To be sure you take maximum advantage of all the features the AVR-2805/985 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference, should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ATTENTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · The preset memory can be set for one component only among the following: CDR/MD, DVD/VDP and DBS/CABLE. The preset codes are as follows upon shipment from the factory and after resetting: TV, VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HITACHI CD, TAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DENON CDR/MD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DENON (CDR) DVD/VDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DENON (DVD) DBS/CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ABC (CABLE) DVD preset codes 0000 DVD-900 DVD-910 DVD-1000 DVD-1200 DVD-1500 DVD-2200 DVD-2800 DVD-2800II DVD-2900 DVD-3800 DVD-5900 DVD-9000 DVM-1800 DVM-1805 DVM-1815 DVM-2815 DVM-4800 0001 DVD-800 DVD-1600 DVD-2000 DVD-2500 DVD-3000 DVD-3300 B Model No. 50 Operating a component stored in the preset memory 1 Press the mode selector button for the component you want to operate. NOTE: · For the DVD player remote control buttons, function names may differ according to manufacturer. Compare with the remote control operation of the various components. 1 2 Operate the component. · For details, refer to the component's operating instructions. Video disc player (VDP) system buttons POWER : Power on/standby (ON/SOURCE) 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 8, 9 : Auto search (cue) 3 : Pause 0~9, +10 : 10 key 1. Digital video disc player (DVD, DVD SETUP) system buttons POWER : Power on/standby (ON/SOURCE) 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 8, 9 : Auto search (to beginning of track) 3 : Pause 0 ~ 9, +10 : 10 key DISC SKIP +: Disc skip (for DVD changer only) DISPLAY : Display MENU : Menu RETURN : Return SETUP : Setup ENTER : Enter ·, ª, 0, 1 : Cursor up, down, left and right 51 3. Video deck (VCR) system buttons POWER : Power on/standby (ON/SOURCE) 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 3 : Pause Channel +, ­ : Channels 4. Monitor TV (TV), digital broadcast satellite (DBS) tuner and cable (CABLE) system buttons POWER : Power on/standby (ON/SOURCE) MENU : Menu ·, ª, 0, 1 : Cursor up, down, left and right ENTER : Enter CHANNEL : Switch channels +, ­ 0~9, +10 : Channels TV/VCR : Switch between TV and video player TV VOL +, ­ : Volume up/down DISPLAY : Switch display RETURN : Return NOTES: · For this CD, CDR, MD and TAPE components, buttons can be operated in the same way as for Denon audio components. · The television can be operated in the DVD/VDP, VCR and TV modes. 52 Learning function If your AV component is not a Denon product or if it cannot be operated using the preset memory, it can be controlled with the accessorious remote control unit by storing its remote control signals in the remote control unit. For some remote control signals it is not possible to "learn" the signals or the device will not operate properly. In such cases use the remote control unit included with the device to operate it. 1 Press the USE/LEARN button with the tip of a pen etc. , to set the learn mode. · Both the mode selector buttons and LEARNED/TX indicator flash. Flashes 2 2 Press the mode button of the equipment for which learning is desired. · Mode button and LEARNED/TX indicator flash. 3 4 Press the button that is to be learned. · Mode button and LEARNED/TX indicator flashed if a button that cannot be "learned" is pressed. Point the remote control units directly at each other and press and hold in the button on the other remote control unit which you want to "learn". 1, 3, 7 6 Other remote control unit To "learn" other buttons, repeat steps 2 to 5. 7 Once the learning operation is completed, press the USE/LEARN button again. The mode button and the LEARNED/TX indicator stop flashing and the learning mode is cancelled. 5 The mode button and the LEARNED/TX indicator lights, release the button on the other remote control unit. · The mode button and the LEARNED/TX indicator start flashing again. Check that the stored codes work properly. NOTES: · If the codes could not be stored, the LEARNED/TX indicator start flashing rapidly. · If the mode button and LEARNED/TX indicator start flashing rapidly, this means that the memory is already full, and the code you have just attempted to store was not stored. To "learn" that code, first perform the resetting operation. (See page 56. ) 53 System call The accessorious remote control unit is equipped with "system call" function allowing a series of remote control signals to be transmitted by pressing a single button. This function can be used for example to turn on the amplifier's power, select the input source, turn on the monitor TV's power, turn on the source component's power and set the source to the play mode, all at a signal button. (1) System call buttons Up to 10 signals each can be stored at the "CALL1" and "CALL2" buttons. 1 (2) Storing system call signals 1 Press the power ON/SOURCE button and the OFF button at the same time. [. . . ] This adjusts the volume of the signals output from the speakers and subwoofer for the different channels in order to obtain optimum effects. Set the frequency (Hz) below which the bass so of the various speaker is to be output from the subwoofer. Large Front L & R 12 ft (3. 6 m) Front L 0 dB Front R 0 dB Center Sp. Small Center 12 ft (3. 6 m) Center 0 dB Default settings Subwoofer Yes Subwoofer 12 ft (3. 6 m) Surround L Surround R Surround Sp. [. . . ]