User manual DENON AVR-800

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. [. . . ] · "ENTER KEYS" is displayed, then the mode display appears. ENTER 8 Press the ENTER button. · "COMPLETE" appears on the remote control unit's display and registration is completed. ENTER SHIFT SHIFT NOTES: · The remote control signals of the buttons pressed while registering the system call signals are emitted, so be careful not to operate the components accidentally (cover the remote sensors, for example). · If you exceed the number of signals that can be registered, "FULL" appears on the remote control unit's display and only the number of signals that can be registered are registered (up to 29 operations). (3) Using the system call function 1 Press the button at which the system call signals have been stored. · The stored signals are transmitted successively. Resetting (1) Resetting the system call buttons 1 Press the power ON/SOURCE button and the OFF button at the same time. · "SET UP" appears on the remote control unit's display. POWER 1 OFF ON / SOURCE OFF ON / SOURCE RC-883 REMOTE CONTROL UNIT TV CD CDR/MD/ TAPE RECEIVER VCR DBS/CABLE VDP DVD DISPLAY MENU 2 3 Press the ENTER button. ENTER SURR. PARA. SETUP TUNING OSD RETURN A/B MEMORY 3, 4, 5 CHANNEL BAND MODE VOLUME TUNING SHIFT 2, 3, 4, 5, 6 SKIP + ENTER + CD SKIP TUNER SHIFT MUTING PHONO 1 CDR/TAPE 2 VDP 3 DVD Use the D and H cursor buttons to display "RESET" on the remote control unit, then press the ENTER button. TUNING ENTER 4 VCR-1 5 VCR-2/V. AUX 6 TV/DBS 7 TV/ VCR TEST TONE 8 0 SPEAKER 9 +10 OUTPUT SURROUND DOLBY/DTS SURROUND DSP SIMU. 5CH / 7CH STEREO BAND MODE SHIFT 6. 1 / 7. 1 SURROUND DIRECT STEREO TUNING MODE INPUT ANALOG EXT. IN SYSTEM CALL CALL 1 CALL 2 BACKLIGHT 36 4 Use the D and H cursor buttons to display "RESET SYS" on the remote control unit, then press the ENTER button. · "SYS SEL" appears on the remote control unit's display. TUNING ENTER q To reset CALL 1 or CALL 2, select "SYS CALL 1" or SYS CALL 2", then press the ENTER button. ENTER SHIFT BAND MODE SHIFT TUNING The remote control unit's display switches as shown below each time the D and H cursor buttons are pressed. RESET PRE RESET ALL RESET LRN RESET SYS w To reset system call settings registered at other buttons, select "SYS MODE", press the ENTER button, press the mode button at which the button is registered, then press the ENTER button again. ENTER SHIFT 5 Press the D and H cursor buttons to select the system call setting to be reset. TUNING 6 MODE BAND "CONFIRM" is displayed. To reset the setting, press the ENTER button while "CONFIRM" is displayed. · "SYS SEL" appears on the remote control unit's display. ENTER TUNING SHIFT The remote control unit's display switches as shown below each time the D and H cursor buttons are pressed. · The mode and the registered number appear on the remote control unit's display. The channel switches on the TV, DBS or CABLE device and playback stops on a CD, MD, tape, DVD, VCR or VDP player. OFF 7 Press the ENTER button. · "COMPLETE" is displayed on the remote control unit's display and the selected code is preset. ENTER SHIFT 40 9 OPERATION Before operating 1 2 3 Refer to "CONNECTIONS" (pages 6 to 13) and check that all connections are correct. (only when operating with the remote control unit) RECEIVER (Remote control unit) Turn on the power. Press the POWER switch (button). ON / STANDBY ON / SOURCE POWER OFF ON / SOURCE RC-883 REMOTE CONTROL UNIT 3 ON/STANDBY Light TV CD CDR/MD/ TAPE RECEIVER (Main unit) (Remote control unit) 2 VCR DBS/CABLE VDP DVD DISPLAY MENU When pressed, the power turns on and the display lights. The sound is muted for several seconds, after which the unit operates normally. When pressed again, the power turns off, the standby mode is set and the display turns off. Whenever the ON/STANDBY button is in the STANDBY state, the apparatus is still connected on AC line voltage. Please be sure to unplug the cord when you leave home for, say, a vacation. 41 Playing the input source TV CD CDR/MD/ TAPE RECEIVER 1 VCR DBS/CABLE VDP DVD DISPLAY MENU SURR. PARA. SETUP TUNING OSD RETURN A/B MEMORY BAND MODE CHANNEL VOLUME TUNING SKIP + ENTER + SKIP TUNER 4 CD SHIFT MUTING PHONO 1 CDR/ TAPE 2 VDP 3 DVD 4 5 VCR-2 /V. AUX 6 TV/DBS 1 Select the input source to be played. Example: CD FUNCTION VCR-1 7 TV/ VCR TEST TONE 8 0 SPEAKER 9 +10 OUTPUT CD 3 SURROUND DOLBY/DTS SURROUND DSP SIMU. [. . . ] The main feature of this format is that because the SL, SR and SB channels are fully independent, the sound can be designed with total freedom and it is possible to achieve a sense that the acoustic images are moving about freely among the background sounds surrounding the listener from 360 degrees. Though maximum performance is achieved when sound tracks recorded with this system are played using a DTS-ES decoder, when played with a conventional DTS decoder the SB channel signals are automatically down-mixed to the SL and SR channels, so none of the signal components are lost. DTS-ESTM Matrix 6. 1 With this format, the additional SB channel signals undergo matrix encoding and are input to the SL and SR channels beforehand. The performance of the encoder used at the time of recording can be fully matched using a high precision digital matrix decoder developed by DTS, thereby achieving surround sound more faithful to the producer's sound design aims than with conventional 5. 1- or 6. 1-channel systems. [. . . ]