User manual DENON AVR-787

[. . . ] AV SURROUND RECEIVER AVR-787 OPERATING INSTRUCTIONS ENGLISH ¢SAFETY PRECAUTIONS SAFETY INSTRUCTIONS Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. [. . . ] In this case, try other surround modes, without worrying about their names, to create a sound field suited to your tastes. 30 ENGLISH ENGLISH Basic Operation Basic Operation Selecting the DSP surround simulation F G, SELECT/ENTER · Select "Default Yes" and press F to reset all the settings. ¢ To operate the surround mode and the surround parameters from the remote control unit 1 <SURROUND MODE>, DH SURROUND PARAMETER Press [DSP SIMULATION]. 5CH/7CH STEREO VIRTUAL MATRIX VIDEO GAME MONO MOVIE ROCK ARENA JAZZ CLUB ¢ Operating the surround mode and the surround parameters from the main unit's panel 1 Use <SELECT/ENTER> to select the surround mode. DIRECT STEREO DOLBY PRO LOGIC IIx DTS NEO:6 5CH/7CH STEREO MONO MOVIE NEURAL SURROUND ROCK ARENA MATRIX JAZZ CLUB VIDEO GAME VIRTUAL SURROUND The 5CH/7CH STEREO mode can be selected directly by pressing [5CH/7CH STEREO]. [CH SELECT], ENTER DHFG 2 Press SURROUND PARAMETER. 2 Perform steps 2 to 4 under "Selecting the DSP surround simulation". SB CH OUT · ON: Surround back channel played. ROOM SIZE: Adjust the imaginary size of the recreated sound field space. (Does not express size of room in which played. ) There are five parameters: "small", "med. s", "medium", "med. l" and "large". EFFECT LEVEL: Adjust the strength of the surround effect. To select the surround mode while adjusting the surround parameters, tone defeat or tone control, press <SURROUND MODE>, then operate the selector. [5CH/7CH STEREO] DHFG ENTER [DSP SIMULATION] SURROUND PARAMETER About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit DELAY TIME: (MATRIX mode only) Adjust the delay time between "0 ms" and "110 ms". 4 Press ENTER or SURROUND PARAMETER. 31 ENGLISH ENGLISH Basic Operation Basic Operation Setting the tone control Adjust the bass and treble to suit your tastes. ¢ When you do not want to adjust the tone Set "Tone Defeat" to "ON" at step 3 in "Adjusting the tone". Using the fader function With this function, the volume of all the front side speakers or all the rear side speakers can be adjusted (attenuated) at once. ¢ Adjusting the tone 1 Press SURROUND PARAMETER. 2 Press D H to select "TONE DEFEAT". In the direct mode, "TONE" cannot be selected. Adjusting the speaker volume 1 Press [CH SELECT]. "S. Back" when surround back speaker set to "1sp". 1 Press [CH SELECT]. Press F side 3 speakers, toGattenuate the volume of allofthe front rear to attenuate the volume all the side speakers. The fader function does not affect the subwoofer. It is possible to adjust so that the volume of the speaker whose volume is the lowest is ­12 dB. 3 D H select 4 Pressset thetolevel. "Bass" or "Treble", then press F G to Press G to select "OFF". Can be adjusted within the range of ­10 dB to +10 dB. 2 Press [CH SELECT] to select the speaker. The settable speaker switches each time this button is pressed. 2 3 5 Press ENTER or SURROUND PARAMETER. 1 2 F 3 Press [F G] to adjust the volume. The SW channel level can be turned off by decreasing it one step from ­12. 0 dB. OFF ´ ­12. 0 dB ´ +12. 0 dB 32 ENGLISH ENGLISH Basic Operation Basic Operation <POWER> CHANNEL <FUNCTION> BAND TUNING Listening to the radio Check that the remote control unit is set to "AUDIO". Auto tuning Auto preset memory This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory. 1 Use <FUNCTION> to select "TUNER" or press [TUNER]. 2 Press BAND to select "AM", "FM" or "XM". When listening to the XM Satellite Radio ( page 34, 35). <ON/STANDBY> SHIFT <PRESET ·> 1 Switch off the unit using <POWER>. 2 Hold <PRESET ·> and press <POWER>. 3 Press [MODE] to set the auto tuning mode. · The "AUTO" indicator lights. · The unit automatically begins searching for FM broadcast stations. 4 Press TUNING. · Automatic searching begins. SHIFT [FM/AM] CHANNEL When the first FM broadcast station is found, that station is stored in the preset memory at channel A1. Subsequent stations are automatically stored in order at preset channels A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1 to E8, F1 to F8 and G1 to G8 for a maximum of 56 stations. Channel A1 is tuned in after the auto preset memory operation is completed. · If tuning does not stop at the desired station, use to the "Manual tuning" operation. · "AM" or "FM" can be selected directly by pressing [FM/AM]. [ON SCREEN] · If an FM station cannot be preset automatically due to poor reception, use the "Manual tuning" operation to tune in the station, then preset it using the manual "Preset memory" operation. · To interrupt this function, press <ON/STANDBY>. Manual tuning 1 Use <FUNCTION> to select "TUNER" or press [TUNER]. 2 Press BAND to select "AM", "FM" or "XM". When listening to the XM Satellite Radio ( page 34, 35). [TUNER] 3 Press [MODE] to set the manual tuning mode. TUNING [MODE] BAND [MEMORY] Check that the display's "AUTO" indicator turns off. 4 Press TUNING. The frequency changes continuously when the button is held in. · When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the "STEREO" indicator turns off. · "AM" or "FM" can be selected directly by pressing [FM/AM]. About the button names in this explanation < > : Buttons on the main unit [ ] : Buttons on the remote control unit Button name only : Buttons on the main unit and remote control unit 33 ENGLISH ENGLISH Basic Operation Basic Operation Preset memory Recalling preset stations XM Satellite Radio AVR-787 is the XM Ready receiver. You can receive XM® Satellite Radio by connecting to the XM Passport System (sold separately) and subscribing to the XM service. 1 Use the "Auto tuning" or "Manual tuning" operation to tune in the station to be preset in the memory. 2 Press [MEMORY]. SHIFT to select the desired memory block (A to CHANNEL to select the desired preset channel 4 Press8). [. . . ] · No digital signal is being input. · Connect securely. · Properly select a digital signal input source. 8 21 21 22 47 Power has turned off and the power indicator is blinking red. Nothing is displayed on monitor. · AVR-787's video output terminals and · Check that the connections are 9, 13 ~ 20 correct. -- · Set the monitor's input selector to · Monitor's input setting is wrong. -- · Player connected with component · Down-conversion is not possible for progressive video signals. [. . . ]