User manual DENON AVR-785S

[. . . ] AV SURROUND RECEIVER RÉCEPTEUR AUDIO-VIDÉO AVR-1905/785 OPERATING INSTRUCTIONS MODE D'EMPLOI FOR ENGLISH READERS PAGE 2 ~ PAGE 70, 138 ~ 142 POUR LES LECTEURS FRANCAIS PAGE 2, 71 ~ PAGE 142 2 We greatly appreciate your purchase of this unit. 2 To be sure you take maximum advantage of all the 2 Nous vous remercions pour l'achat de cet appareil. 2 Pour être sûr de profiter au maximum de toutes les features this unit has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. [. . . ] Example: CD FUNCTION 5 (Main unit) (Remote control unit) To select the input source when ZONE2/REC OUT is selected, press the MAIN button then operate the input function selector. 2 MAIN (Main unit) 2 Select the input mode. · Selecting the analog mode Press the ANALOG button to switch to the analog input. ANALOG (Main unit) (Remote control unit) · Selecting the external input (EXT. IN (Main unit) (Remote control unit) · Selecting the AUTO, PCM and DTS modes The mode switches as shown below each time the INPUT MODE button is pressed. AUTO PCM DTS Input mode selection function Different input modes can be selected for the different input sources. The selected input modes for the separate input sources are stored in the memory. q AUTO (auto mode) In this mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected and the program in the AVR-1905/785's surround decoder is selected automatically upon playback. The presence or absence of digital signals is detected, the signals input to the digital input jacks are identified and decoding and playback are performed automatically in DTS, Dolby Digital or PCM (2 channel stereo) format. If no digital signal is being input, the analog input jacks are selected. w PCM (exclusive PCM signal playback mode) Decoding and playback are only performed when PCM signals are being input. Note that noise may be generated when using this mode to play signals other than PCM signals. e DTS (exclusive DTS signal playback mode) Decoding and playback are only performed when DTS signals are being input. r ANALOG (exclusive analog audio signal playback mode) The signals input to the analog input jacks are decoded and played. IN (external decoder input jack selection mode) The signals being input to the external decoder input jacks are played without passing through the surround circuitry. NOTE: · Note that noise will be output when CDs or LDs recorded in DTS format are played in the "PCM" (exclusive PCM signal playback) or "ANALOG" (exclusive PCM signal playback) mode. Notes on playing a source encoded with DTS · Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. · In some rare cases the noise may be generated when you preform the operation to stop playback of a DTS-CD or DTS-LD. INPUT MODE (Main unit) (Remote control unit) 37 ENGLISH Input mode display · In the AUTO mode AUTO INPUT PCM DTS 3 Select the play mode. Example: Stereo One of these lights, depending on the input signal. DIGITAL ANALOG · In the DIGITAL PCM mode SURROUND MODE SELECT AUTO INPUT PCM DTS DIGITAL · In the DIGITAL DTS mode (Main unit) (Remote control unit) SURROUND MODE AUTO INPUT PCM DTS DIGITAL To select the surround mode while adjusting the surround parameters, tone defeat or tone control, press the surround mode button then operate the selector. · In the ANALOG mode AUTO INPUT PCM DTS ANALOG (Main unit) Input signal display · DOLBY DIGITAL SIGNAL DIGITAL 4 5 Start playback on the selected component. · For operating instructions, refer to the component's manual. Adjust the volume. MASTER VOLUME · DTS SIGNAL DIGITAL · PCM The volume level is displayed on the master volume level display. SIGNAL DIGITAL (Main unit) (Remote control unit) The volume can be adjusted within the range of ­70 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 45, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume is adjusted to "18 dB -- (Maximum value of channel level)". ) Input mode when playing DTS sources · Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "DTS". The DIGITAL indicator lights when digital signals are being input properly. [. . . ] Have you operated the receiver according to the Operating Instructions ?If this unit is not operating properly, check the items listed in the table below. Disconnect the power immediately and contact your store of purchase. Symptom Common problems when listening to the CD, records, tapes and FM broadcasts, etc. · Turn the power on with the remote control unit after turning the POWER switch on. [. . . ]