User manual DENON AVR-770SD

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN610003-3. Se till att det finns möjlighet till god värmeavledning vid montering i ett rack. Unplug the power cord when not using the set for long periods of time. [. . . ] To perform this operation from the remote control unit, check that the mode selector switch is set to "AUDIO". The DTS NEO:6 Cinema or Music mode can be chosen directly by pressing the CINEMA or MUSIC button on the remote control unit during playback in the DTS NEO:6 mode. Select the function to which the component you want to play is connected. To perform this operation from the remote control unit, check that the mode selector switch is set to "AUDIO". (Cinema Equalizer): The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion picture soundtracks. Select this function if the sound from the front speakers is too bright. This function only works in the Dolby Pro Logic II, Dolby Digital and DTS Surround modes. (Dynamic Range Compression): Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds). For listening late at night, or whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in the soundtrack (but with reduced dynamic range). (This only works when playing program sources recorded in Dolby Digital. LFE (Low Frequency Effect): This sets the level of the LFE (Low Frequency Effect) sounds included in the source when playing program sources recorded in Dolby Digital or DTS. If the sound produced from the subwoofer sounds distorted due to the LFE signals when playing Dolby Digital or DTS sources when the peak limiter is turned off with the subwoofer peak limit level setting (system setup menu), adjust the level as necessary. DTS Surround: ­10 dB to 0 dB When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct DTS playback. When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to ­10 dB for correct DTS playback. The same signals those of the surround channels are output from the surround back channels. NOTE: This operation can be performed directly using the "SURROUND BACK" button. The Cinema mode is for use with stereo television shows and all programs encoded Dolby Surround. Panorama Control: This mode extends the front stereo image to include the surround speakers for an exciting "wraparound" effect with side wall imaging. Dimension Control: This control gradually adjust the soundfield either towards the front or towards the rear. Center Width Control: This control adjust the center image so it may be heard only from the center speaker; only from the left/right speakers as a phantom image; or from all three front speakers to varying degrees. Decoding is performed with emphasis on separation performance to achieve the same atmosphere with 2-channel sources as with 6. This mode is effective for playing sources recorded in conventional surround formats as well, because the in-phase component is assigned mainly to the center channel (C) and the reversed phase component to the surround (SL, SR and SB channels). [. . . ] Dolby Virtual Speaker technology uses proprietary technology of Dolby Laboratories to create a virtual surround sound field using only two speakers for the front channels, allowing the user to experience sound as if surround speakers were actually being used. 2 Features of Dolby Virtual Speaker sound B Accurate surround sound field positioning The virtual surround speakers are positioned at 105° to the left and 105° to the right. B Multi-channel programs played according to the producer's intentions The sound of the different channels is played in the position set upon mixing. B Stereo programs played in surround The Dolby Pro Logic II circuit is used together with the Dolby Virtual Speaker circuitry to create a rich virtual surround sound field with stereo programs as well. [. . . ]