User manual DENON AVR-487

[. . . ] AV SURROUND RECEIVER AVR-487 OPERATING INSTRUCTIONS ENGLISH ¢SAFETY PRECAUTIONS SAFETY INSTRUCTIONS Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. [. . . ] q Analog and PCM 2-channel signals (STEREO) w 2-channel signals of Dolby Digital, DTS or other multi-channel format (DOLBY PLIIx Cinema) e Multi-channel signals of Dolby Digital, DTS or other multichannel format (DOLBY/DTS SURROUND) Default settings are indicated in ( ). Setting the Auto Preset Memory Up to 56 FM stations can be preset automatically ( page 30). 1 Press F to start. · "CH" blinks on the display and searching begins. · "Completed" appears once searching is completed. Press 2 OptionENTER to enter the setting and switch to the Setup. 1 Search 3 Press ENTER or H to enter the setting and switch to the Auto Surround Mode setting. COMPLETED 1 Press F G to set. 2 Press ENTER to enter the setting and switch to the Speaker Setup. 1 4 AutoSurr. OFF 2 2 · If an FM station cannot be preset automatically due to poor reception, use the "Manual tuning" operation ( page 31) to tune in the station, then preset it using the manual "Preset memory" operation ( page 31). 20 ENGLISH ENGLISH INPUT MODE STATUS INPUT SELECTOR <ANALOG> DIMMER VOLUME Basic Operation Playing the input source 1 <PHONES> <EXT. IN> <SPEAKER> SURROUND PARAMETER 4 Use VOLUME to adjust the volume. Use INPUT SELECTOR to select the input source you want to play. · The volume level is displayed on the master volume level display. 2 Press INPUT MODE. AUTO EXT. IN PCM DTS ANALOG The volume can be adjusted between the range of ­80 ~ 0 ~ 18 dB. Depending on the channel level settings and the different surround mode settings and when in the down-mix mode, it may not be possible to adjust the volume to 18 dB. Press <ANALOG> to select "ANALOG", <EXT. IN". INPUT SELECTOR VOLUME [MUTING] STATUS AUTO (All auto mode): The type of input signal is detected and the AVR-487's surround mode is switched automatically. Can be selected for sources for which the Digital In Assignment mode ( page 19) is made. The input switches to the analog input terminals is no digital signals are being input. PCM (exclusive PCM signal playback mode) and DTS (exclusive DTS signal playback mode): Played when the various signals are input. Noise may be generated when a mode different from the input signal is set. IN (External decoder input terminal selection mode): The signals input to the various input terminals are played. · Canceling the EXT. IN mode: Press INPUT MODE or <ANALOG> to switch to the desired input mode. IN mode together with a picture, select the input source to which the video signal is connected first, then set the input mode. · The "DIGITAL" indicator lights when digital signals are being input properly. If the "DIGITAL" indicator does not light, check whether the Digital In Assignment mode ( page 19) and connections are correct. · In play modes other than the external input mode, the signals connected to these terminals cannot be played. Cautions when playing DTS sources: · For DTS sources, be sure to connect the device to the digital input terminal and set "AUTO" or "DTS" for the input source. Noise will be generated if you play in the "ANALOG" or "PCM" mode. · When playing DTS signals in the "AUTO" mode, noise may be generated when you first start playing and during searching. If so, play in the "DTS" mode. DIMMER INPUT SELECTOR To lower the subwoofer channel level in the EXT. [. . . ] · < and > ends of batteries inserted in reverse. · Set to a mode other than "STEREO". · Insert batteries properly. -- 3 3 3 -- 3 7 7 Cause Measures Page 14 · Power supply cord not plugged in · Check the insertion of the power securely. · No digital signal is being input. · Connect securely. · Properly select a digital signal input source. 7 21 21 22 19 Power has turned off and the power indicator is blinking red. Nothing is displayed on monitor. · AVR-487's video output terminals and · Check that the connections are 8, 10 ~ 14 monitor's input terminals are not correct. [. . . ]