User manual DENON AVR-4802R

[. . . ] AV SURROUND RECEIVER AVR-4802R OPERATING INSTRUCTIONS AMP MASTER VOLUME INPUT SELECTOR REMOTE SENSOR SIGNAL DIGITAL INPUT PCM PURE DIRECT SURROUND BACK CH SIGNAL OUTPUT DETECT VOLUME LEVEL ON/STANDBY ON/STANDBY AUTO DTS A B ES DSCRT DVD DIGITAL SURROUND SPEAKER HOME THX CINEMA PURE DIRECT 2 We greatly appreciate your purchase of the AVR-4802R. 2 To be sure you take maximum advantage of all the features the AVR-4802R has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] (only when operating with the remote control unit) 3 3 (Remote control unit) Turn on the power. Press the POWER switch (button). ON / STANDBY AMP ON/STANDBY 3 Light (Main unit) (Remote control unit) 2 · When pressed, the power turns on and the display lights. The sound is muted for several seconds, after which the unit operates normally. · When pressed again, the power turns off, the standby mode is set and the display turns off. · Whenever the ON/STANDBY button is in the STANDBY state, the apparatus is still connected on AC line voltage. Please be sure to unplug the cord when you leave home for, say, a vacation. 46 Playing the input source 1 3 5 1 3 2 5 1 Select the input source to be played. Example: CD INPUT SELECTOR (Main unit) (Remote control unit) 2 Input mode selection function Different input modes can be selected for the different input sources. The selected input modes for the separate input sources are stored in the memory. q AUTO (auto mode) In this mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected and the program in the AVR-4802R's surround decoder is selected automatically upon playback. This mode can be selected for all input sources other than PHONO and TUNER. The presence or absence of digital signals is detected, the signals input to the digital input jacks are identified and decoding and playback are performed automatically in DTS, Dolby Digital or PCM (2 channel stereo) format. If no digital signal is being input, the analog input jacks are selected. w PCM (exclusive PCM signal playback mode) Decoding and playback are only performed when PCM signals are being input. Note that noise may be generated when using this mode to play signals other than PCM signals. e DTS (exclusive DTS signal playback mode) Decoding and playback are only performed when DTS signals are being input. r ANALOG (exclusive analog audio signal playback mode) The signals input to the analog input jacks are played. IN (external decoder input jack selection mode) The signals being input to the external decoder input jacks are played without passing through the surround circuitry. NOTE: · Note that noise will be output when CDs or LDs recorded in DTS format are played in the "PCM" (exclusive PCM signal playback) or "ANALOG" (exclusive PCM signal playback) mode. Select the AUTO or DTS mode when playing signals recorded in DTS from a laser disc player or CD player. Note on playing a source encoded with DTS · Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. · Selecting the analog mode Press the ANALOG button to switch to the analog input. ANALOG (Main unit) (Remote control unit) · Selecting the external input (EXT. IN button on the remote control unit) to switch the external input. EXT. [. . . ] Even without the proper environment for playing the SB channel, Dolby Digital Surround EX signals are 100% compatible with existing 5. 1channel playback systems, so they can be played as such. In this case, the SB channel signal is produced as a monaural signal from both the SL and SR channels, so none of the signal components are missing. The effects specific to THX Surround EX (the sense of spatial expression and the positioning of the sound), however, are the same as with conventional 5. 1-channel surround systems. Surround EX is a jointly developed technology of THX and Dolby Laboratories, and is a trademark of Dolby Laboratories. [. . . ]