User manual DENON AVR-4802

[. . . ] AV SURROUND RECEIVER AVR-4802 OPERATING INSTRUCTIONS MASTER VOLUME INPUT SELECTOR ·)) REMOTE SENSOR SIGNAL DIGITAL INPUT AUTO PCM PURE DIRECT SURROUND BACK CH SIGNAL OUTPUT DETECT VOLUME LEVEL ON/STANDBY ON/STANDBY DTS A B ES DSCRT DVD DIGITAL SURROUND SPEAKER HOME THX CINEMA PURE DIRECT PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER AVR-4802 2 We greatly appreciate your purchase of the AVR-4802. 2 To be sure you take maximum advantage of all the features the AVR-4802 has to offer, read these instructions carefully and use the set properly. Be sure to keep this manual for future reference should any questions or problems arise. "SERIAL NO. PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO THE REAR OF THE CABINET FOR FUTURE REFERENCE" 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] · The indicator for the selected program source lights. SELECT 1, 4 2 (Main unit) Display Set the recording mode. · For operating instructions, refer to the manual of the component on which you want to record. To cancel, press the REC/MULTI button and select "SOURCE". 2 PHONO CD TUNER DVD / VCR -1 -2 -3 V. AUX MD / VDP TV / DBS TAPE REC / MULTI (Main unit) NOTES: · Recording sources other than digital inputs selected in the REC OUT mode are also output to the multi source audio/video output jacks. · Digital signals are not output from the MULTI ZONE audio output jacks. [2] Recording Dolby Digital and DTS multichannel sources · With this set it is possible to record Dolby Digital and DTS multichannel signals converted into 2-channel analog signals. · The recording signals are output to the MULTI ZONE OUT, TAPE and VCR output terminals. 1 2 3 Press the REC/MULTI button until "REC OUT SOURCE" appears on the display. REC / MULTI (Main unit) 323 1 Set the input mode according to the source to be played. INPUT MODE (Main unit) Set the surround mode by pressing the DIRECT or STEREO button. · The multichannel digital signals are down-mixed and output to the TAPE and VCR output terminals. DIRECT STEREO 3 3 or or (Main unit) (Remote control unit) 4 36 Set the recording mode. [3] Outputting a program source to an amplifier, etc. , in a different room (MULTI mode) 1 2 Press the REC/MULTI button until "MZONE SOURCE" appears on the set's display. REC / MULTI (Main unit) Select the source you want to record appears on the set's display. · When the AVR-4802 is in the REC OUT mode, the source cannot be output using the M-ZONE 1 buttons on the remote control unit. SELECT 1, 4 2 (Main unit) Display 2 PHONO CD TUNER DVD / VCR -1 -2 -3 V. AUX MD / VDP TV / DBS TAPE 3 4 Start playing the source to be output. · For operating instructions, refer to the manuals of the respective components. When "Multi" is selected for the system setup's multi-zone setting, the source selected here is output from the SB/MULTI speaker terminals. The volume can be adjusted and the input source can be selected using the VOLUME UP and VOLUME DOWN buttons on the remote control unit's "M-ZONE 1" page. NOTES: · The signals of the source selected in the Multi mode are also output from the TAPE and VCR recording output terminals. · Digital signals are not output from the MULTI ZONE audio output jacks. REC / MULTI (Main unit) 37 Playback using the external input (EXT. IN button on the remote control unit) to switch the external input. EXT. IN (Main unit) (Remote control unit) Once this is selected, the input signals connected to the FRONT-L , FRONT-R, CENTER, SURR. -L (surround left) and SURR. -R (surround right) channels of the EXT. IN jacks are output directly to the front (left and right), center and surround (left and right) speaker systems as well as the pre-out jacks without passing through the surround circuitry. In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. IN is selected, the input signals connected to the EL (effect left) and ER (effect right) jacks are output to the PRE OUT (SBL and SBR) jacks. 21 2 Cancelling the external input mode To cancel the external input (EXT. IN) setting, press the INPUT MODE or ANALOG button to switch to the desired input mode. INPUT MODE ANALOG 2 2 1 (Main unit) (Remote control unit) · When the input mode is set to the external input (EXT. IN), the play mode (DIRECT, STEREO, DOLBY/DTS SURROUND, HOME THX CINEMA, WIDE SCREEN, 5CH/7CH STEREO or DSP SIMULATION) cannot be set. NOTES: · In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode. 38 Playing audio sources (CDs and DVDs) The AVR-4802 is equipped with three 2-channel playback modes exclusively for music. [. . . ] With the AVR-4802, the signals further undergo Home THX Cinema processing to achieve a THX Surround EX system. Even without the proper environment for playing the SB channel, Dolby Digital Surround EX signals are 100% compatible with existing 5. 1channel playback systems, so they can be played as such. In this case, the SB channel signal is produced as a monaural signal from both the SL and SR channels, so none of the signal components are missing. The effects specific to THX Surround EX (the sense of spatial expression and the positioning of the sound), however, are the same as with conventional 5. 1-channel surround systems. [. . . ]