User manual DENON AVR-4800

[. . . ] AV SURROUND RECEIVER AVR-4800 OPERATING INSTRUCTIONS START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR MASTER VOLUME INPUT SELECTOR VOLUME LEVEL REMOTE SENSOR CH INDICATOR C R +10 A/B VOLUME DISC SKIP+ L LOCK HOME THX CINEMA DOLBY / DTS SURROUND DIRECT SL S SR LFE SURROUND BACK DSP SIMULATION 5CH/7CH STEREO STEREO MASTER VOL. ON / STANDBY INPUT MODE ANALOG EXT. IN HOME THX CINEMA TAPE-2 MON SURROUND SPEAKER A B AUDIO PHONO CD TUNER DVD VDP TV / DBS VCR-1 VCR-2 V. AUX MD / TAPE-1 TAPE-2 MON CD VIDEO DECK MD MULTI TV MUTING AVR/AVC DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT PHONES 6. 1 / 7. 1 SURROUND DIRECT STEREO DOLBY / DTS SURROUND SURROUND MODE 5CH / 7CH DSP STEREO SIMULATION TUNING PRESET SHIFT DOWN UP BASS TREBLE MEMORY PANEL DISPLAY ON SCREEN RETURN INPUT MODE ANALOG 6CH / 8CH EXT. IN VIDEO SELECT TONE DEFEAT USE/LEARN T. TONE MULTI SET UP STATUS DIMMER MODE SOURCE INPUT REC / MULTI PRECISION AUDIO COMPONENT / AV SURROUND RECEIVER AVR-4800 2 We greatly appreciate your purchase of the AVR-4800. 2 To be sure you take maximum advantage of all the features the AVR-4800 has to offer, read these instructions carefully and use the set properly. [. . . ] INPUT MODE ANALOG EXT. IN This unit's remote control unitFlashes 2 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER 3 B TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT 2 3 4 Set the program switch to the side to be "learned". Set to the AUDIO side for the CD, tape deck or DAT position, to the VIDEO side for the VDP, VCR or TV position. AUDIO AVR/AVC VIDEO MEMORY STATUS DISPLAY ON SCREEN RETURN 1, 8 USE/LEARN T. TONE MULTI SPEAKER DVD SET UP 5 Check that the START LED is lit, then press the button to be "learned" on the other remote control unit. Other remote control unit Set the program switch to the position to be "learned". DECK MD CD MULTI DVD VDP VCR TV This unit's remote control unitFlashes Set the remote control units so they are facing each other, then press the button to be "learned" on this unit's remote control unit. Transmitting windows Lit Other remote control unit 6 Once the START LED turns off and the LEARNED/TX LED lights, release the button on the other remote control unit. This unit's remote control unitFlashes Approx. 5 cm The two LEDs start flashing again. Lit The indicator stops flashing and the START LED lights. The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, DAT and tape deck, the buttons which can be operated with the preset memory for the VCR, VDP and TV. For the TV only, however, the buttons in the section indicated "A" on the diagram above can also be "learned". Use these to "learn" TV channels. 7 8 To "learn" other buttons, repeat steps 2 to 6. Once the learning operation is completed, press the USE/LEARN selector button again. The two LEDs stop flashing and the learning mode is cancelled. Check that the stored codes work properly. NOTES: · Up to 26 codes can be "learned", but this number may be lower if the codes are long. · If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released. · If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. · If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored. To "learn" that code, first perform the resetting operation. (See page 39. ) 36 System call function · The included remote control unit is equipped with a system call function for transmitting multiple remote control signals when a single button is pressed (this is often referred to as a "macro" function). This function can be used to turn on the amplifier's power, select the input source, turn on the monitor TV's power, turn on a source component's power and start playback, etc. , all at the touch of a button. (1) System call buttons The buttons that can be used for the system call function are shown on the table below. A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up to 5 operations can be performed with other buttons. System call signals are already preset at the buttons indicated in the shaded section. System call signals can also be stored at any button on the remote control unit, including the buttons in this section. transmissions 10 10 DVD player (DVD) power on LD player (VDP) power on Receiver input source switched to DVD Receiver input source switched to VDP Receiver input source switched to TV/DBS Receiver input source switched to V. AUX Receiver input source switched to VCR-1 Video (VCR) playback DVD player (DVD) playback LD player (VDP) playback Stored operation 1 Stored operation 2 Stored operation 3 Stored operation 4 Stored operation 5 Stored operation 6 Stored operation 7 Stored operation 8 Stored operation 9 Stored operation 10 DVD (key 5) 5 Receiver power on TV power on VDP (key 6) 5 Receiver power on TV power on TV/DBS (key 9) 5 Receiver power on TV power on V. AUX (key 10) 5 Receiver power on The system call signals for the POWER OFF and POWER ON buttons are transmitted from the remote control unit approximately once every second. The signals for the other buttons (DVD, VDP, TV/DBS, V. AUX, VCR-1 and CD) are transmitted approximately once every 1. 5 seconds. TV power on VCR-1 (key 13) 5 Receiver power on Video (VCR) power on Receiver input source switched to CD TV power on CD (key 14) 5 Receiver power on (2) Using the system call function 1 2 Press the system call button. · The LEARNED/TX LED flashes for 5 seconds. CALL 1 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 2 V. AUX 3 PHONO 2 Press the button at which the desired system call signals are stored while the LEARNED/TX LED is flashing. · The preset signals or the signals you have stored at that button are transmitted in succession. TV/DBS 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN AUDIO AVR/AVC VIDEO DECK MD CD MULTI DVD VDP VCR TUNING SYSTEM SETUP MUTING TV SURROUND PARAMETER TITLE BAND CH SELECT MENU/GUIDE MODE ENTER SELECT 37 (3) Storing signals (4) Clearing system call settings 1, 5 2 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1, 3 2 START SYSTEM CALL LEARNED/TX POWER RC-869 ON / SOURCE SHIFT SET DVD CALL VDP OFF TUNER 1 TV/DBS 2 V. AUX 3 PHONO 1 TV/DBS 2 V. AUX 3 PHONO 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 4 VCR-1 5 CD 6 MD / TAPE-1 CHANNEL 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR 7 VCR-2 8 0 9 TAPE-2 MON TV/VCR +10 A/B +10 A/B VOLUME DISC SKIP+ VOLUME DISC SKIP+ HOME THX CINEMA DOLBY / DTS SURROUND DIRECT HOME THX CINEMA DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. DSP SIMULATION 5CH / 7CH STEREO STEREO MASTER VOL. INPUT MODE ANALOG EXT. IN INPUT MODE ANALOG EXT. IN 3 AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV VDP VCR MUTING AUDIO AVR/AVC VIDEO CD DECK MD MULTI TV MUTING DVD SYSTEM SETUP DVD VDP VCR SYSTEM SETUP TUNING SURROUND PARAMETER TUNING SURROUND PARAMETER TITLE BAND CH SELECT MENU/GUIDE BAND TITLE CH SELECT MENU/GUIDE MODE ENTER SELECT MODE ENTER SELECT MEMORY STATUS DISPLAY ON SCREEN MEMORY STATUS DISPLAY ON SCREEN RETURN RETURN USE/LEARN T. TONE MULTI SPEAKER DVD SET UP USE/LEARN T. TONE MULTI SPEAKER DVD SET UP 1 2 3 Press the SET button. · The START LED and LEARNED/TX LED both flash. SET 1 2 3 Press the SET button. SET Press the button whose settings you want to clear. Press the button at which you want to store the system call signals. [. . . ] This system was developed jointly by Lucasfilm THX and Dolby Laboratories, fusing Lucasfilm's idea of improving spatial expression and achieving a uniform 360 degree sound positioning with Dolby Laboratories' matrix encoding technology. Emphasis was placed on compatibility with the existing system Dolby Digital 5. 1-channel, and the new "surround back (SB) channel" was added to achieve improvements over the conventional 5. 1-channel system in terms of the positioning of the sound at the rear, the acoustic image of sound moving from the two sides to the back as well as sound moving from the front to the center rear with the multi surround speaker systems used in movie theaters, thereby enabling various types of surround sound. The surround back channel signal is a matrix-encoded signal inserted into both the Dolby Digital SL (surround left) and SR (surround right) channels. Upon playback, the signals are decoded by a high precision digital matrix decoder within the Dolby Digital decoder into the SL, SR and SB channels and output as 6. 1 channels of signals. [. . . ]