User manual DENON AVR-1600

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. [. . . ] For some models the remote control unit or the device may not operate properly. In this case, use the learning function (page 53) to store your device's remote control signals in the included remote control unit. 1 Press the power ON/SOURCE button and the OFF button at the same time. · The LEARNED/TX indicator flashes. 1 1 2 Press the mode button of the equipment that is to be entered to a preset memory. · The mode button flashes. 2 3 3 1 4 7 2 5 8 0 3 6 9 Referring to the included List of Preset Codes, use the number buttons to input the preset code (a 4-digit number) for the manufacturer of the component whose signals you want to store in the memory. mode button and the 4 5 When stored correctly, the LEARNED/TX indicator will light. To store the codes of another component in the memory, repeat steps 1 to 4. NOTES: · Depending on the model and year of manufacture, this function cannot be used for some models, even if the your device is listed on the included list of preset codes. · Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and check it out. · The preset memory can be set for one component only among the following: CDR/MD, DVD/VDP and DBS/CABLE. The preset codes are as follows upon shipment from the factory and after resetting: TV, VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HITACHI CD, TAPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DENON CDR/MD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DENON (CDR) DVD/VDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DENON (DVD) DBS/CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ABC (CABLE) DVD preset codes 0000 DVD-900 DVD-910 DVD-1000 DVD-1200 DVD-1500 DVD-2200 DVD-2800 DVD-2800II DVD-2900 DVD-3800 DVD-5900 DVD-9000 DVM-1800 DVM-1805 DVM-1815 DVM-2815 DVM-4800 0001 DVD-800 DVD-1600 DVD-2000 DVD-2500 DVD-3000 DVD-3300 B Model No. 50 Operating a component stored in the preset memory 1 Press the mode selector button for the component you want to operate. NOTE: · For the DVD player remote control buttons, function names may differ according to manufacturer. Compare with the remote control operation of the various components. 1 2 Operate the component. · For details, refer to the component's operating instructions. · The stored signals are transmitted successively. Punch Through (1) Punch through button Buttons used in the CD, CDR/MD, TAPE, DVD/VDP, and VCR modes can be assigned to the buttons shown on the diagram at the right which are not normally used in the TV and DBS/CABLE modes. For example, when the CD mode is set to the punch through mode in the TV mode, the CD mode's PLAY, STOP, MANUAL SEARCH, AUTO SEARCH, PAUSE and DISC SKIP buttons' signals are sent in the TV mode. (2) Making the punch through setting 1 1 4 3 1 Press the power ON/SOURCE button and the OFF button at the same time. · The LEARNED/TX indicator flashes. 2 3 4 Press the 1 (play) button. · TV and DBS/CABLE mode buttons and LEARNED/TX indicator flash. 2 (1) Press the mode button of the equipment for which Punch Through is to be set. · The CD, CDR/MD, TAPE, DVD/VDP, and VCR mode buttons and LEARNED/TX indicator will flash. · The mode button that was set will light. 55 Resetting (1) Resetting "learned" buttons 1 Press the USE/LEARN button with the tip of a pen, etc. , to set the learn mode. · The mode selector buttons and LEARNED/TX indicator flash. Flashes 3 2, 3 2 Press the mode button of the equipment that is to be reset. · Mode button and LEARNED/TX indicator flash. 3 Hold for 4 seconds or longer the mode button of the equipment that is to be reset and the ON/SOURCE button. · The mode button and the LEARNED/TX indicator will again flash, and the learned remote control signal of the selected equipment will be deleted. 4 Press the USE/LEARN button. 1, 4 56 (2) Resetting the punch through setting 1 Press the power ON/SOURCE button and the OFF button at the same time. · The LEARNED/TX indicator flashes. 1 1 3, 4 2 3 4 Press the 1 (play) button. [. . . ] Set the ON/OFF setting of Room EQ, in the case of the surround mode is in Direct or Pure Direct. Set this to switch the Mic Input jack for use for Mic or V. Aux Lchannel input jack. 2. Speaker Setup Speaker Setup Speaker Configuration Input the combination of speakers in your system and their corresponding sizes (SMALL for regular speakers, LARGE for fullsize, full-range) to automatically set the composition of the signals output from the speakers and the frequency response. This parameter is for optimizing the timing with which the audio signals are produced from the speakers and subwoofer according to the listening position. [. . . ]