User manual DENON AVC-A1SR

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Se till att det finns möjlighet till god värmeavledning vid montering i ett rack. Unplug the power cord when not using the set for long periods of time. [. . . ] This operation is possible when the setting for using both surround speakers A and B is made at "Speaker Configuration" in the System Setup Menu. With the exception of the case in [2] below, only the signal connected to the analog input jacks are output from the RECOUT and nulti-room output jacks. [1] Playing one source while recording another (RECOUT mode) Select the source you want to record appears on the set's display. When RECOUT mode is set to "source", with the AVC-A1SR it is possible to output signals encoded in the Dolby Headphone mode from the recording output terminal and record them on a separate recorder. The Dolby Headphone play mode is set when headphones are connected to the PHONES jack during playback in the DOLBY/DTS surround mode. When this is done, signals encoded in the Dolby Headphone mode are automatically output from the recording output terminals (analog and digital) and can be recorded. The play mode switches as shown below each time the button is pressed. -R (surround right), SB-L (surround back left) and SB-R (surround back right) channels of the EXT. IN jacks are output directly to the front (left and right), center surround (left and right) and surround back (left and right) speaker systems as well as the pre-out jacks without passing through the surround circuitry. Select the parameter (jog stick up/down) and select the setting value (jog stick left/right). Select the source you want to record appears on the set's display. When the AVC-A1SR is in the RECOUT mode, the source cannot be output using the MZONE2 buttons on the remote control unit. Input CH parameter 2 CH: Select when the input source being played is a 2-channel source. MULTI CH: Select when the input source being played is a multi-channel source. The signals of the source selected in the MZONE2 mode are also output from the TAPE and VCR recording output terminals. Digital signals are not output from the MULTI ZONE1 audio output jacks. IN (1 or 2), playback in the DIRECT, STEREO, DOLBY/DTS SURROUND, HOME THX CINEMA, WIDE SCREEN, 5CH/7CH STEREO and DSP SIMULATION modes is only possible when DSP MODE is selected for Ext. When the "INPUT CH" parameter is set to "MULTI CH", the "MULTI CH DIRECT" mode is set when the DIRECT button is pressed, and the "MULTI CH IN" mode is set when the DOLBY DTS/SURROUND button is pressed. In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode. 2 Playback using the DENON Link connector Digital transfer and multi-channel playback of DVD audio discs and other multi-channel sources is possible by connecting the AVC-A1SR to a Denon DVD player equipped with a Denon Link connector using the connection cable included with the DVD player. [. . . ] "Dolby Digital Surround EX" is a new movie sound track that greatly enhances the sense of spatial expression and the positioning of the surround channel sound. The result is 360 degrees of movement and moving sound effects that seem to pass right over the listener's head. This system was developed jointly by Lucasfilm THX and Dolby Laboratories, fusing Lucasfilm's idea of improving spatial expression and achieving a uniform 360 degree sound positioning with Dolby Laboratories' matrix encoding technology. emphasis was placed on compatibility with the existing system Dolby Digital 5. [. . . ]