User manual DENON ASD-1R

[. . . ] If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the product into an outlet on a circuit different from that to which the receiver is connected. · Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. I ENGLISH NOTE ON USE: · Avoid high temperatures. [. . . ] & Canada model) r t (For Europe model) y (For China model) NOTE: · Do not use any AC adapter other than the specified one. · The included AC adapter is exclusively for use with this unit. Never use it with other equipment. 1 ENGLISH ENGLISH Getting Started Getting Started Before using Pay attention to the following before using this unit: · Moving the unit To prevent short-circuits or damaged wires in the connection cables, always unplug the power supply cord and disconnect the connection cables between all other audio components when moving the unit. · Cautions on using mobile phones Using a mobile phone near this unit may result in noise. After reading, store this instructions along with the warranty card in a safe place. · Note that the illustrations in these instructions may differ from the actual unit for explanation purposes. q Dock connector w Universal adapter slot e CONTROL terminal (stereo mini plug) r AUDIO OUT terminals t S-VIDEO OUT terminal y DC IN terminal Bottom panel Part names and functions Top panel/Rear panel u u Fixing screw holes iu Use the fixing screw holes (two) to fix the control dock by screw. 15 mm in length) i Communication mode selector (MODE SELECT) qw e r ty 2 ENGLISH ENGLISH Connecting Other Sources Mounting the universal adapter on the control dock Mount the included universal adapter suited for your iPod® to the control dock's universal adapter slot. Main unit Bottom surface of universal adapter Adapter Stamped indication Stamped indication iPod 20GB iPod 40GB mini Photo 20, 30GB Photo 60GB iPod connectable to the ASD-1R 4th generation iPod 20GB 4th generation iPod 40GB iPod mini iPod Photo 30GB/iPod 20GB with color display iPod Photo 60GB/iPod 40GB with color display · A genuine iPod dock adapter can be mounted on this ASD-1R. · To connect an "iPod nano" or 5th generation iPod, use the dock adapter included with the iPod. · The 3rd generation iPod (with Dock Connector) requires the Apple iPod Universal Dock Adapter 3-Pack that fits your iPod model (separately available from Apple Computer, Inc. ) in order to be connected to the ASD-1R. 3 ENGLISH ENGLISH Connecting Other Sources Connecting Other Sources Connection to devices equipped with DOCK CONTROL terminals The iPod can be operated from an amplifier or system device equipped with a DOCK CONTROL terminal connected to the ASD-1R. AC outlet (wall) AC Adapter (Included) AC 120 V, 60 Hz (For U. S. A. & Canada model) AC 230 V, 50 Hz (For Europe model) AC 220 V, 50 Hz (For China model) Monitor S VIDEO IN 1 2 3 4 Set the MODE SELECT switch on the ASD-1R's bottom panel to "DOCK CONTROL". Connect as shown at the left. Also refer to the operating instructions of the device being connected. Connect the included AC adapter to the ASD-1R's DC IN terminal and plug the AC adapter into a power outlet. Load the iPod onto the ASD-1R. or Device equipped with dock control terminal S VIDEO IN (Viewing iPod images) AUDIO IN L R L R L R NOTE: Be sure to switch the communications mode before turning on the ASD-1R's power. The communications mode will not switch if the MODE SELECT switch is operated while the power is on. DOCK CONTROL AV/Control cable (Included) Signal direction Audio signal Video signal OUT IN OUT IN 4 ENGLISH ENGLISH Connecting Other Sources Connecting Other Sources Connecting the ASD-1R and a device equipped with a system control (SYSTEM CONNECTOR) terminal The iPod can be operated using the system remote control unit equipped with system control (SYSTEM CONNECTOR) terminal connected to the ASD-1R. Use the system remote control unit's cassette deck or CD recorder buttons to operate the iPod. For details, see "Remote control buttons and operations" ( AC Adapter (Included) AC outlet (wall) AC 120 V, 60 Hz (For U. S. A. & Canada mode) AC 230 V, 50 Hz (For Europe model) AC 220 V, 50 Hz (For China model) Monitor S-Video cable (Viewing iPod images) Device equipped with system control (SYSTEM CONNECTOR) terminal Pin-plug cable L R 1 Switch the MODE SELECT switch on the ASD-1R's bottom panel. Page 7). TAPE, CD-R: Set the MODE SELECT switch to "TAPE" when connected to a cassette deck, to "CDR" when connected to a CD recorder. 2 3 4 Connect as shown at the left. S VIDEO IN Be sure the MODE SELECT switch is set to the same position in step 1 as the input terminal used for connection. Also refer to the operating instructions of the device being connected. Connect the included AC adapter to the ASD-1R's DC IN terminal and plug the AC adapter into a power outlet. [. . . ] · Check that the iPod is properly connected to the ASD-1R's dock connector. · The AC adapter is not connected to the ASD-1R or a · Check the connections. · Set the monitor's input selector to the proper position for · The monitor's input selection is not properly set. · Check that the communications mode is set to "DOCK CONTROL". [. . . ]