User manual DELPHI SKYFI2 SA10101 Installation Guide

[. . . ] Connect accessories to your SKYFi2 Cradle as shown. 4 Audio Quality Cassette Adaptor: Direct Connect: FM Modulator: Good Better Best The SKYFi2 Vehicle Adaptor Kit offers you many ways of connecting your SKYFi2 to your vehicle's radio. Review and consider your own unique situation when choosing from the three options. Cassette Adaptor For vehicles with a built-in cassette player. Due to its superior audio quality, this configuration is recommended over the wired or wireless FM modulator configurations if a cassette slot is available in the vehicle. Direct Connect The Delphi FM Direct Adaptor (SA10112) (sold separately) can provide audio input through the vehicle's antenna lead. (Some vehicles may require special antenna lead adaptors. ) Wireless FM Modulator For the ultimate ease of installation, SKYFi2 has a built-in wireless FM modulator that allows you to hear XM programming on any nearby FM radio. [. . . ] ­ Warm the vehicle mount adhesive pad by using a hair dryer or by placing the vehicle mount on top of the vehicle's defrost outlet for several minutes with the heater on. Remove the liner from the adhesive pad and adhere to the vehicle's surface. Make sure you accurately place the pad on the first try since in many cases it will bond almost immediately. For best results, do not touch or apply pressure to the vehicle mount for 72 hours. 6. Clip the SKYFi2 vehicle cradle onto the vent or swivel mount (figures 3 and 4). Attach the antenna as explained on page 11 and route the antenna cable as described on page 13. 9 To vehicle dashboard Figure 3. Attach vehicle mount to back of SKYFi2 as shown. 10 Removing swivel mount from your dashboard You can remove the swivel mount from your dashboard by following these steps: 1. Lift one edge of the adhesive pad gently with fingers or the rounded edge of a spoon. Once enough of the edge is loosened to grip with your fingers, pull the pad gently from the mounting surface at a 90-degree angle. Do not use sharp tools that could damage the vehicle's interior. 2. If the pad fails to loosen, warm it with a hair dryer for 2 to 3 minutes to soften the adhesive. Be careful not to apply too much heat, which could damage the mounting surface. If any adhesive remains on the dashboard surface, the adhesive can easily be removed by rubbing your thumb or finger across it. As necessary, use a mild household cleaner to clean the dashboard surface. Caution: Never use a commercial heat gun or a paint-stripping gun. This can damage the unit or your vehicle. XM Antenna Setup For best reception, follow these recommendations: · Mount the XM Antenna on the metal surface of the vehicle roof in the center of an area with at least 12" x 12" of surface area and a minimum of 6" from a window or sunroof. Due to the small size of this antenna, there are many possible locations for installation depending on the vehicle. Improper positioning of the antenna could cause brief interruptions in the signal reception. Middle Front Rear Important: Do not install antenna inside the vehicle passenger compartment. An antenna mounted on the dashboard or on the rear window deck area of the vehicle will likely experience signal interruption issues and must be avoided. Mounting the antenna on a nonmetallic surface will also result in severe degradation in reception. 11 Warning: Failure to properly install the antenna may result in injury to you or others if it becomes detached during an accident. Figure 5. The design flexibility of your XM Antenna allows mounting on many types of vehicles. Trunk mounting of the antenna is an alternative only for hard- or soft-top convertibles with nonmetallic rooftops. All other vehicles should have roof mounting. 12 A suitable compromise between installation location and reception quality must be assumed by the user. [. . . ] Under no circumstances will Delphi be liable for any incidental or consequential damages under this warranty or any implied warranties. These remedies are the customer's exclusive remedies for breach of warranty. This limited warranty only extends to customers who purchase the Products in the United States. Delphi will not be responsible for damage resulting from any (i) deviation from Delphi's operating instructions as printed in Delphi's catalog or on any packaging, labels, or other literature provided with a Product, (ii) installation of a Product in a manner which is inconsistent with Delphi's written instructions, (iii) alteration or modification of a Product, (iv) misuse, (v) neglect, (vi) abuse, (vii) accident, (viii) normal wear and tear, (ix) commercial use, (x) improper storage, (xi) environmental conditions, including excessive temperature or humidity, (xii) service by anyone other than a Delphi authorized repair facility, (xiii) other improper application, installation or operation of the Product, or (xiv) defects or malfunctions of which Delphi is not advised within ten (10) days of the expiration of the limited warranty period. How you (the Customer) can get service: To obtain warranty service, you must return the defective Product with the original receipt to the original place of purchase. If further clarification or additional information is required from Delphi, you may call Delphi at: 1. 877. GO DELPHI (1. 877. 463. 3574). [. . . ]