User manual DELPHI SKYFI SA10034-11B1

[. . . ] CD audio system Owner's Manual This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Requires a subscription from XM Satellite Radio. SA10034-11B1 Owner's Record The model number is located at the bottom and the serial number is located on the label at the back of the Delphi CD Audio System. Refer to these numbers when contacting your dealer regarding this product. Model No. : DELPHI SA10034-11B1 Serial No. : ______________________ WARNING: To prevent fire or shock hazard, do not expose the Delphi CD Audio System to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CONTENTS Section 1 Delphi CD Audio System Components . . 3 Section 3 Basic Operations CD/MP3, AM/FM, Clock Module Playing Audio CD or MP3 Files . [. . . ] The alignment slots on the receiver should line up with the tabs inside the cradle. At the same time, the receiver should be securely seated with the connector. Press the top center of the SKYFi Receiver display, tilting it back into the Delphi CD Audio System with a firm but gentle click. Remove the SKYFi Receiver by reversing this process (Figure 17). 4. Press "Power" on the SKYFi Receiver or Delphi CD Audio System remote to power up SKYFi. If the display reads "ANTENNA" after powering up, check that the antenna connection is secure and completely engaged. Next, change channels (from 0 to 1 or from 1 to 0 if the receiver is not yet activated). If the "ANTENNA" message remains, power down the radio, unplug the antenna, and look for any obvious damage to the connector, jack, or antenna cable. If no damage is detected, reconnect the antenna, turn the unit back on, and change channels again. If the display reads "NO SIGNAL" after powering up, follow the instructions below and on page 9 for positioning the XM antenna and optimizing its signal. Once the Delphi CD Audio System is set up and the SKYFi Receiver is inserted in its cradle, refer to the SKYFi Operating Guide for complete system operation and control information. Positioning the XM Antenna The XM antenna that comes with your Delphi CD Audio System is a high-gain antenna that can receive XM's signal from XM's satellites and/or, depending on where you live, XM's land-based repeaters. It is recommended that the antenna be positioned near a south-facing window or outdoors with a clear view of the southern sky in order to receive the satellite signal. In some cases, it will be possible to receive XM's signal through standard home walls or a roof. To position your antenna, first set up the Delphi CD Audio System as described earlier in this guide. Next, position the antenna until you receive the strongest possible satellite signal (refer to Optimizing XM Antenna Signal, page 9). If a satellite signal is not available, you can optimize your antenna for a terrestrial signal (signal from land repeater, where available). PRESS MENU TO EXIT SECT ION 3 Figure 16: Insertion of SKYFi Receiver Into Cradle Figure 17: SKYFi Receiver Removal From Cradle 8 SATELLITE Terrestrial Figure 18 Optimizing XM Antenna Signal 1. With the SKYFi cradle facing front, press the Power button on the SKYFi Receiver or Delphi CD Audio System remote. Turn the scroll wheel on the SKYFi Receiver or use the category keys on the remote until "Antenna Aiming" is highlighted on the receiver display. With "Antenna Aiming" still highlighted, press the Enter button on the SKYFi Receiver or remote. The display will show the strength of the satellite and/or terrestrial signals. The signal strength is indicated by the number of filled bars (Figure 18). Antenna Mounting/Installation Mounting the Antenna on the Delphi CD Audio System When outdoors with a clear view of the southern sky or in an area of XM repeater coverage, or when receiving a strong signal indoors, you can mount the XM antenna directly on the back of the Delphi CD Audio System. Wind the antenna cable around the tab on the back of the lower tube, leaving several inches of cable free. [. . . ] · Check battery strength; if they are weak, replace all batteries with new ones. · Verify that the CD is a compatible file format (see page 6 for compatible MP3 file formats). · Confirm that your Delphi CD Audio System is in CD mode (CD panel facing forward and locked in postion). · Verify that the CD is a compatible file format (see page 6 for compatible MP3 file formats). [. . . ]