User manual DELPHI DVDM-800 INSTALLATION GUIDE

[. . . ] DELPHI DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE, OR THAT MAY VIOLATE THE LAW. Warning: To reduce the risk of fire or shock hazard, do not expose DVDM-800 to rain or moisture. IMPORTANT An LCD panel and/or video monitor may be installed in a vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation, or navigation. If the LCD panel or video monitor is used for television reception, video, or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in "park" or when the vehicle's parking brake is applied. An LCD panel or video monitor used for television reception, video, or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be placed where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Warning: This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. [. . . ] Also locate a constant power source (+12V DC at all times) as well as a good grounding point. These connection points are typically found at the ignition switch, fuse box, radio, etc. · To gain access to the vehicle's wiring, remove the ceiling panel and any interior trim, using an upholstery hook tool if necessary. · Cut any required access holes (headliner, other trim components, etc. ). · If shroud will be used, additional trimming of the shroud may be required to conform to the vehicle roof. Caution: Take care when removing the dome light and cutting the headliner to not damage the headliner fabric. 7. Recheck all system functions to ensure that wiring is connected properly and that no wires are kinked or pinched. Warning: Failure to properly follow these instructions could result in damage to the vehicle, its electronic system, other property, or personal injury and/or death. MOUNTING DVDM-800 Recommended Tools and Equipment · Upholstery hook tool (for removal of panels, if necessary) · Scribe · #1 and #2 Phillips screwdrivers · Utility knife, razor knife, or shears · Wire strippers · Electrical tape · Multimeter (to verify correct voltages and continuity; Delphi does not recommend using a test light or logic probe for this purpose) Depending on the roof geometry of the particular vehicle in which you are installing DVDM-800, there are three installation options: Attaching the unit directly to the roof supports with the shroud, bolting it into the mounting bracket alone, or installing it with both the shroud and the mounting bracket. See Figure 2. Note: The following mounting sequence may be modified based on the installation option chosen. 5. Route the power and A/V cables and any other component/accessory wiring throughout the vehicle, protecting wiring from sharp edges. For guidance, refer to the wiring diagram on page 6 as well as any instructions provided with other hardware such as gaming systems. Connect all electrical components, insert a DVD, and verify that all system functions work properly prior to final mounting in the vehicle. 1. With panels, trim, and dome light removed, install the video monitor temporarily to the vehicle roof by opening the unit and inserting bolts through the bolt holes directly into the roof supports. Leave a gap between the headliner and the outer flange of the video monitor. Following the contour of the roof, mark the area to be trimmed on the shroud so that it will fill the gap between the headliner and outer flange. 4 3. Using a sharp utility knife or shears, score the plastic along the cutline with several passes, cutting a little deeper each time. When you have cut about halfway through the plastic, bend it back and forth several times for a clean cut. Remove the video monitor and hold the shroud in place, checking the fit. Attach DVDM-800 and shroud using screws through the perimeter screw bosses. If using the mounting bracket, secure it to the roof support cross-members. [. . . ] Positive switched systems turn the interior lights on by supplying voltage to them. The wires at the dome light will help you determine which system you have. · On a positive switched system, with all vehicle doors closed and lights out, both wires at the dome light will rest at ground. When the light is turned on, one of these wires will switch to +12V DC (the vehicle's switching wire). [. . . ]