User manual DELONGHI TRSW 0920

[. . . ] - When scrapping the appliance, respect legislation on the disposal of oil. - The use of an extension lead is not recommended, as overheating of the extension lead may occur during the operation of the heater. - As with any electrical appliance, whilst the instructions aim to cover as many eventualities as possible, caution and common sense should be applied when operating your appliance, particularly in the vicinity of young children. The appliance is fitted with a safety device which will switch it off in case of accidental overheating. To reset, contact an authorised service centre. [. . . ] Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size. After replacement of a fuse in the plug, the fuse cover must be refitted. If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference. 3 Stretto General instructions 1. Check that neither the heater nor the power cable has been damaged in any way during transportation. Your heater is suitable for either freestanding or wall mounting usage. Make sure that no pieces of polystyrene or other packaging material have been left between the elements of the appliance. It may be necessary to use a vacuum cleaner to help eliminate the small pieces. Fitting the castors Remove the castors, wheels and assemblies from the polystyrene packaging. In the unlikely event that there are any parts missing please contact our customer services department on 0845 600 6845 who will send you the part by return. Insert the castors into the pins of the feet and push them all the way in until a click can be heard (fig1) Make sure that they are in tightly by pulling the wheels gently. Attach the castor assembly into the base of the control panel by inserting the guiding ridges between the control panel and the first element and between the end panel and the last element; insert the location lug into its housing and lock the castor assembly to the product by inserting the eye screw and screwing it in tightly (fig1). Finally turn the heater over to its upright position, ensuring you do not damage the wheels. fig. 1 Stretto 4 Ceiling The wall mounting kit should contain: 2 x Upper brackets (A) 1 x Lower brackets (B) 250mm 5 x screws 1. Floor Important Minimum distances Before drilling into any wall ensure no electrical cables are present from surrounding in the area, especially hidden in the wall. (if in doubt, consult a qualwalls/ furnishings ified electrician). 150mm Installation wall-mounting D A A D D = B = fig. 3 fig. 4 2. Following carefully the dimensions as indicated below (the distance depends on which model you have purchased) mark distance "D" on your wall. Model 1 Kw 1, 5 Kw 2 Kw 2, 5 Kw Distance D D D D mm 140 mm 210 mm 280 mm 385 mm 3. Line up the centre of the holes of the brackets "A" with the marked lines (indicated in fig 3 and 4 as the dashed lines)ensuring that the 2 brackets are level, mark the holes to be drilled. [. . . ] The heater has 3 heat settings: Eco/night-time (min power): Press the upper switch (the red light on the switch will come on) Medium power: Press the lower switch (the red light on the switch will come on) Maximum power: Press both switches (the red lights on both switches will come on) To turn the appliance off, press both switches on the 0 position so the red lights are off and unplug at the mains. We suggest that for night-time/ background heat or on days when temperatures are not particularly cold, select minimum output to optimise savings on energy consumption. Eco/night-time I II Adjusting the thermostat When the room has reached the desired temperature, turn the thermostat dial slowly in an anti-clockwise direction until you hear a click. This temperature will be regulated automatically and kept constant by the thermostat. Frost protection function Turn the thermostat dial fully anti-clockwise so the is showing. [. . . ]