User manual DELONGHI TRSW 0815 T

[. . . ] Important Before drilling into any wall ensure no electrical cables are present in the area. Fig. 2 Minimum distances from surrounding walls/ furnishings 250mm 150mm 150mm 150mm D A A D = B = fig. 3 D fig. 4 2. Following carefully the dimensions as indicated below (the distance depends on which model you have purchased) mark distance "D" on your wall. mm Model Distance 1 Kw 1, 5 Kw 2 Kw 2, 5 Kw D D D D 140 mm 210 mm 280 mm 385 mm 3. [. . . ] The heater has 3 heat settings: Eco/night-time (min power): Press the upper switch (the red light on the switch will come on) Medium power: Press the lower switch (the red light on the switch will come on) Maximum power: Press both switches (the red lights on both switches will come on) To turn the appliance off, press both switches on the 0 position so the red lights are off and unplug at the mains. We suggest that for night-time/ background heat or on days when temperatures are not particularly cold, select minimum output to optimise savings on energy consumption. Please note that the min power setting will remain on, whilst the heater is switched on to maintain a comfort background heat. Adjusting the thermostat When the room has reached the desired temperature, turn the thermostat dial slowly in an anti-clockwise direction until you hear a click. The thermostat will now keep the temperature in the room constant, turning the heater on and at the minimum power to save energy. Frost protection function Turn the thermostat dial fully anti-clockwise so the is showing. When set in this way, the appliance will switch on automatically only if the room temperature falls below 5°C, to prevent freezing at minimum energy consumption. * Using the timer If you wish to use the timer, position the switch in the middle position . 21 20 19 16 Setting the correct time Check the time on your watch. (16. 00), turn the dial in a clockwise direction until the number 16 is lined up with the triangular pointer (fig. 6). The timer is in effect an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the clock must be re-set. 5 pointer fig. 6 Stretto operating time 21 20 19 g. 7 To program the timer 1) Set the operating times by pushing in the notches on the dial corresponding to the period required (fig. 7) (each notch represents 15 mins. ) 2) Make sure that the timer indicates the correct time (see instructions on setting the correct time). Once programmed in this way, the appliance will repeat the preestablished program every day, if the selector is in the position. Stretto 16 Timer override If you wish to override the timer settings, push the timer switch to position 1 (fig. 8) manual (timer override). To return to timed operation push the switch back to the middle position (fig. 8). NOTE: if the timer switch is at the 0 position (fig. 8), the heater is off and will not operate). 1 Manual (timer override) Timer operation 0 Heater off fig. 8 Cleaning and maintenance The heater should not require any maintenance. However before attempting to clean the heater, unplug from the mains and wait for it to cool (this should take around 30 minutes). If necessary, remove concentrated areas of dirt with a vacuum cleaner. 6 - Do not use the heater in a bathroom or in the vicinity of bathtubs, wash basins, showers or swimming pools. - Never rest the power cable on the heater's elements while it is hot. - The heater must be positioned at least 50cm from furniture or other objects. - If the power cable is damaged, it must be replaced by the manufacturer or an authorised technical service centre. - It is normal for the heater to make `crackling' noises during its first use (or if it has not been used for a long time). If repairs are necessary which call for the opening of the heater, they must be done only by the manufacturer or an authorised service centre. - In the unlikely event of oil leakage, contact the manufacturer or an authorised service centre. - Do not use this appliance in rooms which have a floor area smaller than 4m2 as this may lead to overheating. [. . . ] The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician. [. . . ]