User manual DELONGHI RH 40 REG

[. . . ] The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. WARNING * WARNING: DURING THE LIGHTING PROCEDURE A "LOOSE FLAME" CAN APPEAR FOR A SHORT TIME (LESS THAN 10 SECONDS). OPERATE THE CONTROL SWITCH STAYING ON THE SIDE OR ON THE BACK OF THE HEATER AND NOT IN FRONT OF IT. Place the gas cylinder in the gas cylinder compartment and connect the regulator to the cylinder as shown below. [. . . ] 4. Model: RADIANT First position: (A1) for low, 1 burner is lit giving 1400watts of heat Second position: (3) for maximum, 3 burners are lit giving 4000watts of heat Third position: (2) for medium, 2 burners are lit giving 2600watts of heat Pre Ignition Ignition Low Maximum Medium Model: SRI First position: ( ) for low, 1 burner is lit giving 1400watts of heat Second position: ( ) for maximum, 3 burners are lit giving 4000watts of heat Third position: ( ) for medium, 2 burners are lit giving 2600watts of heat Pre Ignition Ignition Low Maximum Medium 5 OPERATING THE HEATER - Model: SRI2 with thermostat WARNING: DURING THE LIGHTING PROCEDURE A "LOOSE FLAME" CAN APPEAR FOR A SHORT TIME (LESS THAN 10 SECONDS). OPERATE THE CONTROL SWITCH STAYING ON THE SIDE OR ON THE BACK OF THE HEATER AND NOT IN FRONT OF IT. * · Lighting your heater for the first time or if a long time has passed since last used fit the regulator to the cylinder value as previously described outside or in a well ventilated area for 30 minutes to burn off any residue. Depress the CONTROL SWITCH on top of the heater and hold down for 10 seconds, the control knob should be aligned with the "·" then turn it 90° left or right to position " " to activate the piezoelectric starter you should hear a click and see a small spark at the pilot flame. When the pilot light is lit hold the control switch down for 20-30 seconds (if released before this the right panel and pilot light may go out). After releasing the control switch you can now regulate the heat by turning the red thermostat knob anticlockwise to position "+", to ignite the 3 burners. When the room has reached the desired temperature, turn the thermostat knob clockwise until the 2 burners on the left go off. This way, the appliance will automatically maintain the set temperature by cycling between maximum output (3 burners) and minimum output (1 burner) and vice versa. Pre Ignition Ignition Adjustable red thermostat TURNING THE HEATER OFF · Depress the control switch and turn the knob to the "·" position the right hand panel will remain alight. (Requirements of the gas association New Zealand) · Turn the gas cylinder OFF at the valve by turning the cylinder valve clockwise. Ensure that the pilot flame extinguishes indicating that gas is no longer available. Note with all models: Please try to turn the control knob without forcing and pushing downward, to be sure that the control knob is locked on an adjusting position you require. 6 CHANGING THE GAS CYLINDER · Ensure the heater is switched OFF to the "·" position and the gas cylinder valve is CLOSED. · Unscrew the hand wheel anticlockwise until the regulator is separated from the gas cylinder valve. · If using a new cylinder and there is little colour in the burner it could be due to inert gas or air present in the cylinder. If this is the case run it on maximum for a period of 1 hour in a well ventilated area. If this does not work please take your bottle back for purging. CAUTION: Never disconnect the regulator from the cylinder if the heater is operating. If you smell gas, turn off the heater and gas cylinder immediately, take the appliance outside and contact your service agent, retailer or gas supplier. VENTILATION ­ USE ONLY IN A WELL VENTILATED ROOM · Never use in bedrooms, bathrooms or when asleep as adequate ventilation cannot be assured. · Ensure ventilation is more than 72cm2 eg; window must be opened at least 20mm (2cm) in the room which the heater is being operated. · Adequate ventilation must be provided in rooms which the heater is used. This ensures removal of the products of combustion and allows the entry of replacement air. It should also reduce the possibility of condensation occurring. SAFETY DEVICES The heater you have purchased is fitted with safety devices which come on in the event of malfunctioning, while the appliance is in use. If the pilot light accidentally goes out, or if the room is not sufficiently ventilated, the safety device will block the gas flow, causing the heater to go off. 7 MAINTENANCE/SERVICING · Your gas heater is fitted with an approval gas regulator and hose. [. . . ] Slowly turn the gas on and brush the connectors with soapy water or liquid detergent - a gas leak will form bubbles. Special care should be taken if the Heater is on a surface where it can move or twist on its wheels or castors if knocked by a child or dog, etc. 8. The back panel must be fastened onto the back of the heater with the gas bottle inside the heater when in use. 9 TROUBLE SHOOTING SYMPTOM Pilot will not light 1. 5. FAULT No spark Gas cylinder not turned on Regulator not connected Insufficient LPG Dust in the analyser REMEDY 1. [. . . ]