User manual DELONGHI PINGUINO PAC02

[. . . ] The unit can also be used as a "temporary" installation for use in any room with a window or french window; this "temporary" installation can be used at any time until it is ready for permanent installation. Note. : In either case, check that the unit is resting on at "perfectly level" surface. If necessary, use the 2 castor stops for the front castors. 30 cm PERMANENT INSTALLATION WITH PLUG AND FLANGE The outlet holes must be connected to the outside of the building and cannot be made in any wall or panel. A1 in a window pane A2 through the wooden base-section of a glass door A3 in the wall 24 Ø 95 mm Height of outlet: within the range indicated by the dotted line in the figure below. When the unit is not in use, the outlet hole should be sealed with the stopper supplied. Temporary installation: The outlet holes can be connected in a number of ways: fixed hook In any event, for maximum cooling efficiency the window should be closed as much as possible. It is advisable : -- to keep the outlet free of any obstruction; -- to lower the blind partially, without obstructing the outlet, thereby reducing exposure to direct sunlight and indoor/outdoor air exchange. INSTALLATION FOR HEATING FUNCTION (Model CT300H) The unit is simply placed in the room to be heated; there is no need for the discharge hose to be installed. ELECTRICAL CONNECTIONS -- The mains supply, suitable for domestic electrical appliances, must correspond to the power requirements of the air conditioner (power consumption value shown in Table 1). [. . . ] 2) For permanent installation, place the appliance near the wall or window outlet. Make sure it is standing on a level surface and fit the special shock absorbers/castor stops underneath the castors. Never stretch the hose. HOW TO PREPARE WATER CONTAINER Use only clean, salt-free tap water. The water is essential for the air cooling operation and is discharged in the form of steam through the exhaust outlet. A container full of water lasts for a period that depends on a number of conditions such as temperature, humidity, insulation, exposure of the room, number of people present, etc. When the container is empty, the appliance automatically changes function from water to air. At the same time, the quantity of air discharged from the rear hose will increase. Open the water container compartment door, tip the container forwards and lift up to remove. Remove the cap, pull out the extendable tube and fill the container, standing it on the floor. After filling, replace the extendable tube, screw the cap on tightly and return the container to its place, making sure the word FRONT is facing out. During "water condensation" cooling function and in particularly quiet surroundings (eg. This may be regarded as perfectly normal. Attention: Do not use water containing cooking salt or decalcified water which has been decalcified through the use of certain salts. 26 AIR COOLING FUNCTION If the air cooling function of air-conditioner is chosen, it is not necessary to fill the water container. FINAL CHECK In order to obtain maximum performance from your air-conditioner, make sure that: -- doors and windows in the room to be air-conditioned are closed (except for temporary installation, in which case a window must be left partially open). CLOSE THE WINDOWS CLOSE THE DOORS DRAW THE CURTAINS -- the room is well shaded from direct sunlight by drawing curtains and/or partially lowering blinds or shutters, to avoid excessive energy consumption LOWER THE BLINDS -- the intake and outlet vents are free of any obstruction at all times -- there are no sources of heat in the room. DO NOT COVER THE AIR-CONDITIONER IS NOW READY FOR USE, so let's now take a look at the controls. CT300H) ON/OFF pilot light ON/OFF button A B C Heating pilot light air-conditionig/ heating button Timer notches Timer ON/OFF pilot light Selecting fan speed button Thermostat SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. CT250) (see control panel on the opposite page) Plug the appliance into the mains. Select the "programmed" or "non programmed" mode (see previous page) Select the fan speed required pressing "Fan speed" key C. AIR-CONDITIONING Turn the thermostat to Max. The ON/OFF signal lamp will come on. The appliance comes on If not, refer to pg. 34 To switch off the appliance, press key A (ON/OFF main switch). 31 IMPORTANT WARNINGS · · · · This appliance has been manufactured for use in home air conditioning and should not be used for other purposes. It is dangerous to modify or otherwise alter in any way the characteristics of this appliance. The appliance must be installed according to the national technical systems regulations. In case reparations should become necessary, please always contact only the Technical Service Centres authorised by the manufacturer. The reparations done to the air conditioner by incompetent or unauthorised technicians can be dangerous. This appliance must be used exclusively by adults; do not allow children to play with this electrical appliance. This appliance must be connected to an effective grounded power source. In case the use of an extension cord should be necessary, consult a specialised electrician. CLEANING EXTERNAL HOUSING Clean with a damp cloth and rub over with a clean dry cloth. [. . . ] 1) Switch off the appliance and disconnect the plug; 2) Open the water container compartment door and remove the container; 3) Remove the plug from the drainage tube situated at the back of the appliance and empty the water into a bowl; 4) Once the container has been fully drained, replace the plug; 5) Remove any dirt from the surface below the container, rubbing with a cloth. CONTROLS AT BEGINNING OF SEASON Check that the power supply cable and the plug are in perfect condition. Make sure that the system has been grounded and that the wire is not frayed and has not become disconnected. Please make sure to strictly follow the installation instructions. END OF SEASON OPERATIONS 1) De-scale the unit. 35) 2) Remove all traces of residual water using the drainage tube placed at the rear of the appliance (see page 22) 3) Let the fan run for about half an hour to dry the inside of the air-conditioner 4) Switch off the unit and disconnect the plug from the power supply. [. . . ]