User manual DELONGHI PINGUINO CT300

[. . . ] 5 PARTS SUPPLIED Exhaust hose 1 Stopper + flange 1 Castor stop 2 De-scaling fluid 1 Window nozzle 1 Suction cup set 1 23 INSTALLATION FOR AIR-CONDITIONING FUNCTION Our air-conditioner is portable and versatile: it can be used as a permanent installation or wise easily moved from one room to another. The appliance must be fitted at least 30 cm. from the surrounding walls. 30 cm 30 cm When installed permanently, all air discharged from the rear hose is extracted from the room in which the appliance is installed. Check that the room (particularly if it is small) is not "air-tight"; a drop in pressure could cause a malfunction and thereby activate the safety switch. [. . . ] Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. The unit can be used in either programmed or nonprogrammed mode. 21 20 19 16 4) Select the desired function as shown in the chart overleaf. NON-PROGRAMMED MODE In case the programmed functioning is not desired, it is not necessary to vary the program; in this case, it will be sufficient to turn the TIMER to the OFF position. TIMER ON/OFF BUTTON 28 HOW TO START UP THE CONDITIONER (Mod. CT300H) (see control panel on the opposite page) Insert the plug into the electrical outlet and press the A button The warning light will turn on Select the "programmed" or "non programmed" mode (see previous page) Select the button corresponding to the desired function: AIR CONDITIONING/HEATING AIR-CONDITIONING HEATING The button (C) must be released. In the opposite case, see page 34. The button (C) must be pressed. In the opposite case, see page 34. Select the fan speed required pressing "Fan speed" key B. In the heating with ventilation mode, the fan always operates at maximum speed and once the desired temperature is reached, the ventilation function stops. To switch off the appliance, press key A (ON/OFF main switch). Nota: The "TIMER ON" pilot light will only come on with programmed mode. (*) Note We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold). When the desired temperature has been reached, turn the thermostat slowly away from the maximum cooling position until the appliance switches off. The air-conditioner is now programmed to maintain the exact temperature at all times. 29 CONTROL PANEL (Mod. CT300 ON/OFF pilot light ON/OFF button ) A B working pilot light C Timer notches Timer ON/OFF pilot light Timer ON/OFF button Selecting fan speed button Thermostat SETTING THE TIMER The programmer/timer, like all clocks, must be set to the exact time. (16. 00), turn the dial in a clockwise direction (following the direction of the arrow) until the number 16 is lined up with the triangular pointer (the arrows indicates 4:00 P. M. approximately ). PROGRAMMED MODE 1) Release B TIMER button 2) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) 3) Check that the timer indicates the correct time (see instructions on setting). Operating time Funzionamento 21 20 19 16 21 20 19 16 arrow pointer Note: Never turn the dial in an anti-clockwise direction!The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. Note: To override the programmed operating times, simply press the ON/OFF key. NON-PROGRAMMED MODE 1) B TIMER button must be pressed 2) Select the desired function as shown in the chart on the following page. Note For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. Before beginning any cleaning or maintenance operation, always disconnect the appliance plug from the electrical outlet. [. . . ] · clean filter The appliance does · The safety thermostat on the heating element not heat the environhas been activated. CT300H only) · to reset the unit, disconnect it from mains for a few minutes, eliminate the cause of overheating and then reconnect. SERVICING In case of malfunction turn off and disconnect the air-conditioner from power outlet and contact the nearest Service Centre for qualified assistance. 34 Periodic Servicing (IMPORTANT) This appliance should be de-scaled whenever the calcium deposit becomes excessive (on average after 400 operating hours) or in any event at least once every season. INSTRUCTIONS FOR DE-SCALING You will need: 1/4 liter de-scaling fluid (supplied with appliance) 1 liter clean water = 80% dilution a) Remove the container from the unit and drain away any water left in the collecting tray with the drainage tube. Pour 1/4 liter of de-scaling fluid and 1 l clean water into the collecting tray situated under the container, at the bottom of the unit. [. . . ]