User manual DELONGHI PACW 160HP

[. . . ] IMPORTANT SAFEGUARDS · Use this appliance only as described in this instruction manual. As with all electrical equipment, whilst the instructions aim to cover as many eventualities as possible, caution and common sense should be applied when operating and installing this appliance. · This appliance is designed for home air conditioning and must not be used for other purposes. · It is dangerous to modify or alter the characteristics of the appliance in any way. [. . . ] Three speeds are available: Maximum speed: for maximum fan power Medium speed: reduces noise levels but still maintains effective fan operation. Low speed: for silent operation In this mode, AUTO speed cannot be selected. HEATING MODE (FIG. 22) CERTAIN MODELS ONLY This is ideal in spring and autumn when outdoor temperatures are not particularly severe. When using the appliance in this mode, the air hose does not need to be attached. In heating mode, as well as fitting the air exhaust hose, you must also attach the condensate drain hose to drain the water removed from the room (see the section: "Preparing for use"). To set this mode correctly: · Press the MODE button a number of times until the heating symbol appears. · Select the target temperature by pressing the or button until the corresponding value is displayed. 22 In this mode, fan speed is selected automatically by the appliance and cannot be set manually. N. B. -When operating in very cold rooms, the appliance defreezes automatically, momentarily interrupting normal operation. During this operation, it is normal for the noise made by the appliance to change. - In this mode, you may have to wait a few minutes before the appliance starts giving out hot air. - In this mode, the fan may operate for short periods, even though the set temperature has already been reached. 23 SMART MODE (FIG. 23) The appliance chooses automatically whether to operate in air conditioning, fan or heating (certain models only) mode. To set this mode: · Press the MODE button a number of times until the SMART symbol appears. For safety reasons, when the appliance is operating in heating mode, the fan speed could differ from the set speed. N. B. : in SMART mode, you should always fit the condensate drain hose as the appliance may also operate in heating mode. 12 12 DESCRIPTION OF THE REMOTE CONTROL 2 3 4 5 9 10 11 12 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Air conditioning symbol Dehumidifying symbol Fan symbol Heating symbol (certain models only) WATERSAVE symbol Ioniser symbol (certain models only) Fan speed indicator SMART symbol BOOST symbol SLEEP symbol AUTOFAN indicator MODE button (selects the modes) FAN button Increase (+) and decrease (-) temperature button ON/Standby button Signal transmission Selected temperature scale indicator Clock Timer ON symbol Timer OFF symbol Reset button (resets the appliance to the original settings) Timer ON button SET button Timer OFF button SLEEP button °C or °F selection button Swing button (function not available in these models) WATERSAVE button Ioniser button (certain models only) BOOST button 4 3 2 21 15 14 16 23 24 10 12 5 22 9 11 25 20 17 18 19 26 28 29 27 30 35 31 34 32 33 USING THE REMOTE CONTROL Point the remote control at the receiver on the appliance. The remote control must be no more than 7 metres away from the appliance (without obstacles between the remote control and the receiver). Do not drop it or expose it to direct sunlight or sources of heat. 13 MAX 7 metres INSERTING OR REPLACING THE BATTERIES · Remove the cover on the rear of the remote control (fig. 24); · Insert two R03 "AAA" 1. 5V batteries, making sure they are in the correct position (see the instructions inside the battery compartment); · Replace the cover. 24 If the remote control unit is replaced or discarded, the batteries must be removed and disposed of in accordance with current legislation as they are harmful to the environment. THE TIME SETTING After having inserted the batteries, the clock on the display flashes until the time is set. Hold the button down to run rapidly through first the minutes, then the tens of minutes. · Once the correct time has been reached, release the button and press the SET button to confirm. · To cancel the settings programmed on the remote control and restore the original settings, press the RESET button lightly with the point of a pencil or pen. USING THE REMOTE CONTROL UNIT The first part of the controls on the remote control are the same as those on the control panel of the appliance (fig. You should therefore refer to the instructions in the chapter Operating the appliance from the control panel to: - turn the appliance on - select the operating mode (AIR CONDITIONING, DEHUMIDIFYING, FAN, HEATING or SMART) and the fan speed. - set the required temperature 25 26 The following section describes the additional functions corresponding to the controls on the bottom part of the remote control. BOOST FUNCTION (FIG. [. . . ] · Clean the dust filters and (in certain models) the air purifying filters. · Place the power cable in the special rear cable compartment (fig. · Cover the appliance to avoid dust. 41 42 FORCED DRAINING If you need to completely empty the appliance of water (for example, to move it to another location or put it away at the end of the season), you must follow the forced draining procedure. Proceed as follows: · Attach the continuous drain hose and make sure it drains into a suitable container or drain (max. [. . . ]