User manual DELONGHI PACS 1200HP

[. . . ] · Always transport the appliance upright or resting on one side, with short movements only. Before moving the appliance, empty the condensate pan in the indoor unit and the base of the outdoor unit. You are therefore recommended to dispose of them in special differentiated waste collection containers. · The refrigerant gas R410A conforms to EC regulations on the environment. [. . . ] In particular cases, if there is excessive humidity, the condensate is drained through a hole in the base. To drain the water that forms, use the condensate drain connector 19 supplied, which must be fitted on the base of the outdoor unit (see Figure 8). This can then be connected to a rubber hose Note: If appropriate, the external unit can be protected with the protective cover 22 fixing it with the screw provided. The outdoor unit should be protected from the sun, rain, snow and drips from the roof. POSITIONING THE OUTDOOR UNIT The outdoor unit can be placed on a terrace or balcony (Fig. 12 The outdoor unit can also be installed on a window sill, if this faces onto a balcony (Fig. De'Longhi is not liable for any damage to people or things caused by the positioning of the unit in a manner not compliant with the basic standards of safety. 23 ENGLISH Buttons and indicators on the indoor unit BUTTONS AND INDICATORS ON THE INDOOR UNIT MANUAL OPERATION BUTTON RED LIGHT YELLOW LIGHT GREEN LIGHT SIGNAL RECEIVER INDICATOR LIGHTS These turn on according to the function selected or indicate any operating anomalies. FUNCTION OFF AIR-CONDITIONING DEHUMIDIFYING FAN HEATING RED LIGHT on on YELLOW LIGHT on - GREEN LIGHT on on - ANOMALY ALARM RED LIGHT flashing YELLOW LIGHT flashing GREEN LIGHT flashing see "troubleshooting" on page 32 MANUAL OPERATION This operating mode is to be used only when the remote control is inoperative (broken, lost, flat batteries). Press the manual operation button until selecting the desired function (air-conditioning, dehumidifying, fan, heating, smart, off). Refer to the indicator lights and the table above to identify the mode selected. For each mode selected, the appliance will automatically choose the optimum values for maximum comfort. This appliance is fitted with a safety system that prevents the compressor from starting until at least 3 minutes have elapsed since it last went off. 24 The remote control THE REMOTE CONTROL Inserting the batteries · Remove the protective cover (see figure). · Insert two new batteries (not rechargeable) making sure the (+) and (-) are in the correct positions. NB: Alkaline batteries should be used (LR03). 1 2 When replacing or disposing of the remote control, the batteries must be removed and disposed of according to the legislation in force, being harmful to the environment. If the remote control is not be used for a certain length of time, remove the batteries. CORRECT USE · Aim the remote control at the signal receiver on the air-conditioner (Fig. · Maximum distance: around 7 metres (without obstacles between the remote control and the receiver). · The remote control should be handled with extreme care and respect: without dropping it, without exposing it to direct sunlight or near sources of heat. 25 ENGLISH Description of the remote control THE REMOTE CONTROL A. MODE button Selects the operating mode (air conditioning, dehumidifying, fan and heating). Buttons for SETTING THE ROOM TEMPERATURE Set room temperature or program the timer. FAN button Sets fan speed to automatic, high, medium or low in sequence. SMART button ( ) When this button is pressed, the appliance automatically establishes the most suitaHigh ble operating mode for maximum comfort. Low H. SUPER button ( I H G F SWING FAN A B B E D C THE DISPLAY Signal transmission Air-conditioning indicator Dehumidifying indicator Fan indicator Heating indicator SUPER indicator SMART indicator SLEEP indicator High Automatic fan speed Low High ) Starts or stops rapid cooling (in the rapid High cooling mode, the fan operates at high speed with the temperature automatically set to Low 18°C). NB: the settings are displayed even when the air conditioner is off. I. High fan speed Medium fan speed Low Low fan speed Used to set the temperature in SMART mode or the level of dehumidification. 26 Functions AIR-CONDITIONING MODE · Press the button to turn the appliance on. · A beep indicates that the air-conditioning unit is on and the symbol flashes on the display. · Press the MODE button a number of times until the air-conditioning symbol appears on the display. [. . . ] If they are very dirty, immerse in warm water and rinse a number of times. After washing, leave the filters to dry, then replace them. 31 ENGLISH Troubleshooting TROUBLESHOOTING If something is not working, the problem may at times be simple to resolve. Carefully check these brief instructions before contact your local Authorised Service Centre. PROBLEM The air-conditioner doesn't work · · · · · · CAUSE no electricity it is not plugged into the mains the timer is set incorrectly air filter dirty temperature set incorrectly the air intake/outlet grilles are blocked · · · · · · REMEDY wait plug into the mains set the timer correctly clean the air filter set the temperature correctly clean the grilles Insufficient cooling/heating Particular odour in the room Water leaks from the indoor unit of the air-conditioner · air filter dirty · · · clean the air filter See page 21 to install the appliance correctly unplug the appliance and contact the service centre · · incorrect installation of the appliance pump malfunction The remote control indicator is weak or inexistent · · flat batteries batteries inserted the wrong way round · · change the batteries check the polarity of the batteries (+) and (-) wait for three minutes The air conditioning unit does · not operate for about three minutes after turning it on the safety device has tripped · The compressor · switches on and off periodically · the air-conditioner is working in dehumidifying mode the antifreeze safety device has tripped The three indicator · lights flash operating anomaly · unplug the appliance, wait a few minutes and then turn the appliance on again. If the problem persists, contact the service centre. SERVICE If following these checks the malfunction remains, contact your nearest authorised service centre, specifying the model of the appliance and the type of defect. [. . . ]