User manual DELONGHI PACL 16A

[. . . ] The refrigerant gas R410a conforms to EC regulations on the environment. Keep the appliance at least 50 cm away from flammable substances (alcohol etc) or pressurised containers (e. g. aerosol cans). DESCRIPTION 1 air outlet grille 2 control panel 3 castors 4 handles 5 evaporator air intake grille 6 air exhaust hose housing 7 condenser air intake grille 8 drain hose cover 9 power cable 10 flange cap 11 air exhaust hose 12 window outlet 13 suckers 14 castor locks 15 remote control unit (certain models only) 16 adjustable window bar (certain models only) 20 What is the Pinguino ENGLISH ing the summer, you feel comfortable at a temperature of between 24 and 27° C with a relative humidity of about 50%. During the summer, you feel comfortable at a temperature of between 24 and 27° C with a relative humidity of about 50%. [. . . ] The most suitable temperature for the room during the summer varies from 24 to 27°C. You are recommended, however, not to set a temperature much below the outdoor temperature. DEHUMIDIFYING MODE Ideal for reducing the humidity in a room without lowering or raising the temperature (spring or autumn, damp rooms, rainy spells, etc). In dehumidifying mode, the appliance selects fan speed automatically. 26 Fan mode FUNZIONE VENTILAZIONE HEATING MODE (CERTAIN MODELS ONLY) To set operation of the appliance correctly, press the "+" (G) or "-" (I) buttons until the desired temperature is displayed. In heating mode, the fan speed is selected automatically by the appliance. SETTING THE TIMER The timer can be used to delay appliance start up or shut down. This avoids wasting electricity by optimising operating periods How to programme delayed start up · Plug the appliance into a mains socket and press the ON/STAND-BY button (A), then select the required operating mode and other settings (temperature, fan speed, etc). · Press the TIMER button (H): the last timer setting or the preset value 6. 0 h flashes on the display. · Use the + (G) or - (I) buttons to set the number of hours delay before the appliance comes on. If the "+" (G) or "-" (I) buttons are pressed for more than 2 seconds, the time runs rapidly up to a maximum of 24 hours. Press the timer button again within a few seconds to confirm the setting. If the setting is not confirmed within a few seconds, the display resets to stand-by. With the timer activated, the countdown before the programmed start up time is displayed. How to programme delayed shutdown · Delayed shutdown can be set with the appliance in any operating mode - air conditioning/dehumidifying/fan/heating (certain models only). · Press the Timer button (H) the last timer setting or the preset value 6 . · Use the + (G) or - (I) button to set the number of hours delay before the appliance goes off During the first ten hours, you can select half hour intervals. If the "+" (G) or "-" (I) buttons are pressed for more than 2 seconds, the time runs rapidly up to a maximum of 24 hours. Press the timer button again within a few seconds to confirm the setting. At the set time, the air conditioner shuts down and remains in stand-by. To cancel the timer programme, press the timer button (H). 27 ENGLISH Adjust fan speed by pressing the FAN button (P). In this mode, AUTO cannot be selected. Self-diagnosis SELF-DIAGNOSIS The appliance has a self diagnosis system to identify a number of malfunctions. IF . . . IS DISPLAYED LOW TEMPERATURE (FROST PREVENTION) . . . WHAT SHOULD YOU DO? When the appliance is operating in air conditioning or dehumidifying mode, this device prevents the formation of ice. The appliance starts up again automatically when the defrosting process is completed. pf PROBE FAILURE (SENSOR DAMAGED) FULL TANK If this is displayed, contact your service centre. see page 33 "end of season operations" 28 Using the remote control unit ENGLISH 21 DRY FAN HEAT USING THE REMOTE CONTROL (certain models only) CORRECT USE OF THE REMOTE CONTROL · Point the remote control at the receiver (M) on the air-conditioner. [. . . ] Pull out the 2 drain hoses, take off the caps and let all the residual water flow out (figure N). When all the water has been drained, place the caps back on the hoses and put the hoses back inside. Clean the filters and dry thoroughly before putting them back. L 2. M). N intake grille dust filter M 33 Troubleshooting PROBLEM The air conditioning unit does not start · · · CAUSE no electricity it is not plugged into the mains the safety device has tripped · · · REMEDY wait plug into the mains contact your service centre The air conditioning unit works for a short time only · · the air exhaust hose has a constriction the air exhaust hose is blocked · · · position the exhaust hose correctly check there are no obstacles obstructing air discharge eliminate the bends · The air conditioning · unit works, but does · not cool the room · · · there are bends in the air exhaust hose window open there are heat sources in the room (burner, lamp, etc) the exhaust hose is detached air filters clogged the air conditioning unit is not powerful enough for the conditions or size of the room · · · · close the window eliminate the heat source connect the exhaust hose clean or replace the filters Particular odour in the room The air conditioning unit does not operate for about three minutes after turning it on appears on the display / PF/ · air filter clogged · clean or replace the filter · the safety device has tripped · wait for three minutes · See "self-diagnosis" section 34 Guarantee/technical specification GUARANTEE AND TECHNICAL ASSISTANCE The conditions of the guarantee and technical assistance are given on the certificate supplied with your appliance. TECHNICAL CHARACTERISTICS: see rating plate " " " " Max. [. . . ]