User manual DELONGHI PACF 130ECO

[. . . ] Should repairs be necessary, contact the nearest authorised Repair Service Centre. In the case that the power cable becomes damaged, this must be substituted only by specialised personnel authorised by the manufacturer. This appliance is to be used by adults only; keep children away from it. Before cleaning or maintenance operations, always unplug the unit from the socket. [. . . ] As with all household appliances installation, operation and conservation should be carried out prudently and following common sense. · · · DESCRIPTION 1 Air delivery grille 2 Control panel 3 Wheels 4 Handles 5 Housing for hose 6 Cord winder 7 Air intake grill 8 Condensation tank 9 Drainage tube 10 Plug 11 Function selector 12 Air conditioning led 12 Air conditioning/dehumidifying led (mod. F130eco) 13 Ventilation led 14 Full tank light 15 Thermostat knob 16 Flange 17 Air exhaust hose 18 Window attachment 19 Suckers 20 Blocking device 15 ENGLISH GB 3-02-2003 17:10 Pagina 16 Setting up The following instructions will help you set up your air conditioning unit as efficiently as possible. The appliance must always be installed for use taking care that there are no obstacles blocking the ventilation and exhaust fans. AIR CONDITIONING WITHOUT INSTALLATION FOR INSTANT TEMPORARY USAGE With just a few simple operations, Pinguino will restore comfortable conditions in your room: · Fix the air outlet hose 17 n to the coupling 5 · With a double casement window, use the suckersWith a double casement window, use the suckers 19 provided to hold the two halves of the window together (fig. C). on the back of the unit as shown in figu- re A. 1 2 A · Fix the window attachment 18 to the end of the hose 17 . · Open the window or French window slightly and place the window attachment 18 as shown in figure B. C B 16 GB 3-02-2003 17:10 Pagina 17 Setting up AIR CONDITIONING WITH INSTALLATION Pinguino can also be semi-permanently installed · Fit the flange 16 supplied to the hole. · Fix the hose 17 to the coupling on the back of the unit (figure A). ge 16 as shown in the figure E. MAX115 cm E 30 cm MIN 50 cm 30 cm To install, proceed as follows: · Make a hole in a wall communicating with the outside or through the pane of a window. Respect the height and dimensions given in figure D When the hose 17 is not attached, close the hole with the bung on the flange 16 . NOTE: When the unit is installed semi-permanently, we recommend leaving a door slightly open (1 cm is enough) to ensure an adequate exchange of air. DEHUMIDIFICATION (mod. F130 eco only) Position the appliance in the room without inserting the hose; in this way the dehumidified air will exhaust directly into the room in a window pane in the wood sill of a window in the wall: for optimum results, insulate the section of the wall with suitable insulating material. D 17 ENGLISH · Attach the end of the hose 17 to the flan- GB 3-02-2003 17:10 Pagina 18 Turning on and Selecting functions ELECTRICAL CONNECTION Before plugging in check that: · the mains supply corresponds to the value shown in the specifications table; · the socket and the mains lead correspond to the power requirements of the appliance; · the socket is suited to the plug 10 , otherwise have the socket replaced; · the socket is properly grounded. The manufactures cannot be held responsible for any damages due to failure in following normal safety procedures. Replacement of the power cable must be carried out by qualified personnel. AS AIR CONDITIONER With the unit turned off, the function selector 11 is in the "O" position. Rotate the function selector dial clockwise: · Place the large star symbol in line with the reference mark to operate the unit in air conditioning mode at maximum fan speed. · Place the small star symbol in line with the reference mark to operate the unit in air conditioning mode at minimum fan speed. Now set the required temperature by rotating the room thermostat dial Note The temperature is not expressed in degrees. We therefore recommend rotating the room thermostat dial 15 to the maximum cool position. When room temperature has reached the required level, rotate the thermostat dial SLOWLY clockwise until the thermostat is activated, turning the unit off. This programs the unit to the precise level of comfort required which will then be automatically maintained by the thermostat with considerable energy savings. When regulating the thermostat, the air conditioning function is temporarily interrupted and the unit continues to operate in fan/ventilation only mode. In this way, the appliance keeps the air temperature in the room homogeneous. Note: cool air is discharged from grill after a delay of three to five minutes. 1 IN NORMAL CONDITIONS, CONDENSATION IS DISPOSED OF AUTOMATICALLY. WHEN THE HUMIDITY IS PARTICULARLY HIGH, AN EXCESS OF CONDENSATION MAY BUILT UP IN THE TANK. WHEN THIS 14 HAPPENS, THE INDICATOR LIGHT 8 SHOULD . INDICATING THAT THE TANK BE EMPTIED. IF THIS PROBLEM IS RECURRENT YOU MAY DISCHARGE THE EXCESS WATER FROM THE TANK 8 DIRECTLY INTO A DRAIN. THE TUBE SHOULD BE INSERTED INTO THE HOLE PROVIDED AFTER REMOVING THE RUBBER BUNG MAKE SURE THE TANK 8 IS PUT BACK CORRECTLY OTHERWISE THE LIGHT 14 WILL REMAIN ON (SEE FIGURE) AIR FILTRATION WITH FAN Rotate the function selector 11 anti-clockwise. [. . . ] · Do not obstruct the air intake grille 7 or outlet grille 1 ; · Make sure there are no heat sources in the room. lower the blinds or draw the curtains · Make sure the unit is located on a level floor. If necessary, place the two blocking devices 20 under the front wheels 3 . do not cover 20 GB 3-02-2003 17:10 Pagina 21 Cleaning Before cleaning or maintenance, always turn the unit off by placing the selector in the "O" position and unplug from the mains. CLEANING THE EXTERNAL UNIT We recommend cleaning the unit with a slightly damp cloth then drying with a dry cloth. [. . . ]