User manual DELONGHI PAC A130HPEM

[. . . ] Important safeguards · Use this appliance only as described in this instruction manual. As with any electrical appliance, the instructions aim to cover as many situations as possible. Caution and common sense should be used when operating and installing this air conditioner. · This appliance has been manufactured to cool and dehumidify domestic environments and must not be used for other purposes. [. . . ] Note: - When operating in very cold rooms, the appliance may defrost automatically, momentarily interrupting normal operation. During this operation, it is normal for the noise made by the appliance to change. - In this mode, you may have to wait a few minutes before the appliance starts giving out hot air. - In this mode, the fan may operate for short periods, even though the set temperature has already been reached. Note: With high humidity conditions the display could show " Empty the internal circuit as shown in the para" graph "END OF SEASON OPERATIONS" 28 Operation SMART MODE The appliance chooses automatically whether to operate in air conditioning, fan or heating (certain models only) mode based on the set temperature and current room temperature. To set this mode: · Press the MODE button a number of times until the SMART symbol appears. For safety reasons, when the appliance is operating in heating mode, the fan speed could differ from the set speed. GB BOOST FUNCTION Ideal for the summer to cool rooms rapidly. While this function is selected, it is not possible to set the temperature or change fan speed. Hold the button down to run rapidly through first the minutes, then the tens of minutes and then the hours. · Once the correct time has been reached, release the button and press the OK button to confirm. · To cancel the settings programmed on the remote control and restore the original settings, press the reset button lightly with the point of a pencil or pen. USING THE REMOTE CONTROL The first set of buttons on the remote control are the same as those on the control panel of the appliance. You should therefore refer to the instructions in the chapter Operating from the control panel to turn the appliance on, select the operating mode (AIR CONDITIONING, DEHUMIDIFYING, FAN, HEATING or SMART) and the fan speed. The following section describes the ADDITIONAL FUNCTIONS corresponding to the controls on the bottom part of the remote control. 31 Using the remote control BOOST FUNCTION Ideal for the summer to cool rooms rapidly. While this function is selected, it is not possible to set the temperature or change fan speed. Note:- BOOST function cannot be set during HEATING mode. SLEEP FUNCTION This function is useful for the night as it gradually reduces operation of the appliance and turns it off after 8 hours. To set this function correctly: · Select the operating mode (air conditioning, dehumidifying, smart or heating (certain models only) as described above. The appliance operates in the previously selected mode with the lowest possible fan speed. The SLEEP function maintains the room at optimum temperature without excessive fluctuations in either temperature or humidity and with silent operation. Fan speed, room temperature and humidity vary gradually to ensure the most comfortable conditions. During air conditioning, the temperature increases by 2°F (1°C) after 60 minutes and a further 2°F (1°C) after 2 hours. In dehumidifying mode, the dehumidifying power of the appliance is partially reduced every hour for the first two hours. In heating mode, the temperature drops by 2°F (1°C) every hour, for 3 hours. [. . . ] This delay is part of normal operation. The appliance has a self diagnosis system · to identify a number of malfunctions. See the self-diagnosis chapter. The unit will not heat · The unit takes several minutes to produce · warm air Wait. This delay is part of normal operation. 37 Technical specifications TECHNICAL SPECIFICATION Power supply voltage see rating label Max. absorbed power during air conditioning " Refrigerant " Cooling capacity " Absorbed power heating " (certain models only) LIMIT CONDITIONS Room temperature for air conditioning 69, 8 ÷ 95°F (21° ÷ 35°C) Room temperature for heating 50° ÷ 77°F (10° ÷ 25°C) Transport, filling, cleaning, recovery and disposal of refrigerant should be performed by a technical service centre appointed by the manufacturer only. The appliance should be disposed of by a specialist centre appointed by the manufacturer only. NEVER TRANSPORT OR TURN THE APPLIANCE UPSIDE DOWN OR ON ITS SIDE. [. . . ]