User manual DELONGHI PAC A120LE QUICK GUIDE

[. . . ] We know that the Pinguino will maintain your environment pleasingly comfortable at all times. With best wishes De Longhi America, Inc. If you have any questions about the operation or service of your Pinguino, please call our toll-free service number 1-800-322-3848 or 1 - 877-235-1052 in the U. S. (905) 2381313 in Canada. 3 5751000300 PAC290U GB 18-01-2001 16:42 Pagina 4 see rating label SPECIFICATIONS Power supply voltage Frequency Cooling capacity: With water With air Current consumption Water tank capacity Air flow capacity Room thermostat (34° to 102°F) Dimensions: width height depth in. 8500* 7500* 6, 5/ 990 30. 65 212 adjustable 22", 05 28", 74 15", 35 97 R 22 Overload relay lb. [. . . ] 1/2 inch is enough). 7 4". 17 , , 5751000300 PAC290U GB 18-01-2001 16:42 Pagina 8 TEMPORARY INSTALLATION Note: In both cases (permanent and temporary installations) make sure that the Pinguino is positioned on level ground. If necessary use the two caster stops for the front casters This installation makes it easy to use Pinguino in any room, provided there is a window or a door: it allows you to use the Pinguino immediately (Fig. If you have a sash window, place the bracket on the window sill, extend the bracket fully within the window frame and lower the window onto the bracket. Insert the nozzle of the exhaust hose into the slot, then connect the hose to the air conditioner (Fig. Thanks to the wing nut, it's possible to use the window bracket also for sliding windows. Position the hole of the bracket so to allow a correct installation of the exhaust hose (see the following instructions). Note: Additional exhaust hoses are avilable through Dè longhi America. For best results we do not recommend using more than one. 30 cm window bracket fig. 7 PREPARING THE UNIT FOR USE 1) Fit the exhaust tube in place; if your conditioner is supplied with a bayonet tube, it is fitted as illustrated in the diagram. 2) For permanent installation, place the appliance near the wall or window outlet. Make sure it is standing on a level surface and fit the special shock absorbers/castor stops underneath the castors. 1 2 1) Water collects at this point 2) Bend this section 3) Bend this section fig. 8 NO YES YES ELECTRICAL CONNECTION Check that the power supply voltage is 115 V ~ 60 Hz. N. B: For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold). When the desired temperature has been reached, turn the thermostat slowly away from the maximum cooling position until the appliance switches off. The air-conditioner is now programmed to maintain the exact temperature at all times. After switching the appliance off, wait at least 3 min. before switching on again. 4 4 4) Select the desired function as shown in the chart overleaf. Note: To override the programmed operating times, simply press the ON/OFF key. NON-PROGRAMMED MODE 1) B TIMER button must be pressed 2) Select the desired function as shown in the chart on the following page. 10 5751000300 PAC290U GB 18-01-2001 16:42 Pagina 11 HOW TO START UP THE CONDITIONER (see control panel on the previous page) Plug the appliance into the wall socket. Select the "programmed" or "non programmed" mode (see previous page) Select the fan speed required pressing "Fan speed" key C. AIR-CONDITIONING Key A ON/OFF (conditioning) must be released Turn the thermostat to Max. ON/OFF signal lamp (conditioning) will come on. The appliance comes on. 14. To switch off the appliance, press key A (ON/OFF main switch). 11 5751000300 PAC290U GB 18-01-2001 16:42 Pagina 12 MAINTENANCE PRECAUTIONS fig. 16 During cleaning and normal maintenance operations remember to disconnect plug. CLEANING OF EXTERNAL HOUSING Use only mild soap and water. 17 QQ , , QQ , , Under no circumstances should appliance be washed with runing water. [. . . ] 23 Remove dust with a vacuum cleaner Rinse with running water fig. 24 Cleaning procedure To remove dust deposited on filter, use a vacuum cleaner. After washing, leave filter to dry before replacing. END OF SEASON OPERATIONS 5) Remove exhaust hose. 7) Cover appliance with a polyethylene bag to prevent dust from entering. [. . . ]