User manual DELONGHI PAC A 85

[. . . ] Do not install near sources of heat · Keep the appliance at least 50 cm away from flammable substances (alcohol etc) or pressurised containers (eg aerosol cans). · Always transport the appliance upright or resting on one side. Before moving the appliance, empty the internal circuit completely of water. · When putting the appliance away, do not cover with plastic bags. [. . . ] Press the MODE button (O) until the indicator light corresponding to the required mode lights up: Light (F) Light (E) Light (C) : air-conditioning mode : dehumidifying mode : fan mode 24 AIR-CONDITIONING MODE " " Ideal for hot muggy weather when you need to cool and dehumidify the room. To set this function correctly, press the "MODE" button until the " " light comes on, then press the + (G) or - (I) buttons until the required temperature is displayed. Then select the fan speed by pressing the FAN button (P) until the indicator light corresponding to the required fan speed lights up: (HIGH) the air conditioner operates at maximum to reach the required temperature as rapidly as possible. (MED) reduces noise levels but still maintains a good level of comfort. (LOW) for silent operation AUTO: the appliance automatically selects the most suitable fan speed in relation to the temperature set on the digital display (the graphics on the display move). The most suitable temperature for the room during the summer varies from 24 to 27°C. You are recommended, however, not to set a temperature much below the outdoor temperature. DEHUMIDIFYING MODE Ideal for reducing the humidity in a room without lowering or raising the temperature (spring or autumn, damp rooms, rainy spells, etc). In dehumidifying mode, the appliance selects fan speed automatically. FUNZIONE VENTILAZIONE Adjust fan speed by pressing the FAN button (P). In this mode, AUTO cannot be selected. 25 SETTING THE TIMER The timer can be used to delay appliance start up or shut down. This avoids wasting electricity by optimising operating periods How to programme delayed start up · Plug the appliance into a mains socket and press the ON/STAND-BY button (A), then select the required operating mode and other settings (temperature, fan speed, etc). · Press the TIMER button (H): the last timer setting or the preset value 6. 0 h flashes on the display. · Use the + (G) or - (I) buttons to set the number of hours delay before the appliance comes on. If the "+" (G) or "-" (I) buttons are pressed for more than 2 seconds, the time runs rapidly up to a maximum of 24 hours. Press the timer button again within a few seconds to confirm the setting. If the setting is not confirmed within a few seconds, the display resets to stand-by. With the timer activated, the countdown before the programmed start up time is displayed. How to programme delayed shutdown · Delayed shutdown can be set with the appliance in any operating mode - air conditioning/dehumidifying/fan. · Press the Timer button (H) the last timer setting or the preset value 6 . · Use the + (G) or - (I) button to set the number of hours delay before the appliance goes off. If the "+" (G) or "-" (I) buttons are pressed for more than 2 seconds, the time runs rapidly up to a maximum of 24 hours. Press the timer button again within a few seconds to confirm the setting. At the set time, the air conditioner shuts down and remains in stand-by. [. . . ] if necessary, place the castor locks under the front wheels; 9 close doors and windows 10 close curtains 11 do not cover the appliance 30 CLEANING Before cleaning or maintenance, turn the appliance off by pressing the button on the control panel or remote control, wait for a few minutes then unplug from the mains socket. CLEANING THE CABINET You should clean the appliance with a slightly damp cloth then dry with a dry cloth. Never wash the air conditioner with water. Never use petrol, alcohol or solvents to clean the appliance. Never spray insecticide liquids or similar. 12 CLEANING THE AIR FILTERS To keep your air conditioner working efficiently, you should clean the silver ion filter every week of operation. If it is very dirty, immerse in warm water and rinse a number of times. After washing, leave the filter to dry and replace it. START - END OF SEASON OPERATIONS START OF SEASON CHECKS 13 Make sure the power cable and plug are undamaged and the earth system is efficient. [. . . ]