User manual DELONGHI PAC 60

[. . . ] · The appliance should not be installed where the atmosphere may contain combustible gases, oil or sulphur, or near heat sources. · Remember to perform the descaling procedure at the end of each season (see page 25). In areas where the water is particularly hard (rich in minerals), the use of a commercial anti-lime product added to the water is recommended. If this is not possible secure the unit at an angle, do not lie horizontally. · Before transporting the unit drain the condensation collecting-tray and tank. [. . . ] Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. 21 ENGLISH 1) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) 16 16 GB 11-01-2001 14:41 Pagina 22 Selecting functions AIR CONDITIONING FUNCTIONS To turn the unit on in air conditioning mode, proceed as follows: 1. Press the 9 TURBO POWER (only for PAC60) The Turbo Power mode was conceived to provide the appliance with a greater cooling potential. This is particularly useful when you want to bring the temperature of a very warm room quickly down to a more comfortable level. In this case: Make sure that the tank is full of water (see page 22); Make sure that the function selector switch 18 is in the large crystal position. button 10 (the signal light "I" will come on). 2. Rotate the function selector 18 dial anticlockwise: · Place the large star symbol in line with the reference mark to operate the unit in air conditioning mode at maximum fan speed (the signal light 21 will come on, and then, after 3 minutes the signal light 14 will come on ). · Place the small star symbol in line with the reference mark to operate the unit in air conditioning mode at minimum fan speed (the signal light 21 will come on, and then, after 3 minutes the signal light 15 will come on ). Now set the required temperature by rotating the room thermostat dial 19 . Press the Turbo Power button 20 . After reaching the desired temperature, you can release the Turbo Power button and reposition the selector switch to the small crystal. Doing so will make the operation quiter. VENTILATION/FILTRATION Rotate the function selector 18 clockwise. · Press the button 10 (the signal light "I" 9 will come on). · Place the large symbol (or the symbol ) in line with the reference mark to operate the unit at maximum fan speed. · Place the small symbol (or the symbol ) in line with the reference mark to operate the unit at minimum fan speed. (the signal light 16 will come on). Note The temperature is not expressed in degrees. We recommend that you turn the thermostat dial to the maximum position. When the desired room temperature has been reached, slowly turn the thermostat in a clockwise direction until it arrives at the position where a click can be heard. The temperature selected in this way will automatically be regulated and maintained, and save energy. When regulating the thermostat, the air conditioning function is temporarily interrupted and the unit continues to operate in fan only mode. In this way, the appliance keeps the air temperature within the room even. PURIFICATION FILTER (Only for some models) In addition to dust, this purification filter is able to capture even the smallest sized particles and impurities (up to 0. 003 millimetres), such as cigarette smoke. The purification filter should never be used with the dust filter, which is also included with the appliance. If you wish to use the purification filter: Remove the purification filter from the filter housing; Remove the aspiration grill 6 (fig. Remove the purification filter from its packaging. Delay on Start Up 1. A special safety device will delay the start of air conditionig by approximately 3 to 5 minutes when switching between functions or on initial start up. [. . . ] If it does not fit your socket, the plug should be cut off from the mains lead, and on appropriate plug fitted, as below. warning: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a mouldedon type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. [. . . ]