User manual DELONGHI PAC 47

[. . . ] · The appliance should not be installed where the atmosphere may contain combustible gases, oil or sulphur, or near heat sources. · Remember to perform the descaling procedure at the end of each season (see page 25). In areas where the water is particularly hard (rich in minerals), the use of a commercial anti-lime product added to the water is recommended. If this is not possible secure the unit at an angle, do not lie horizontally. · Before transporting the unit drain the condensation collecting-tray and tank. [. . . ] You may also experience a slight delay between changing from one function to another. VENTILATION/FILTRATION Rotate the function selector 13 clockwise. · Press the button 12 (the signal light "I" 11 will come on). · Place the large symbol in line with the reference mark to operate the unit at maximum fan speed. · Place the small symbol in line with the reference mark to operate the unit at minimum fan speed. AIR CONDITIONING FUNCTIONS To turn the unit on in air conditioning mode, proceed as follows: 1. Press the button 12 (the signal light "I" 11 will come on). HEATING Rotate the function selector knob 13 counter clockwise to the symbol: 2. Rotate the function selector 13 dial anticlockwise: · Place the large star symbol in line with the reference mark to operate the unit in air conditioning mode at maximum fan speed. · Place the small star symbol in line with the reference mark to operate the unit in air conditioning mode at minimum fan speed. Now set the required temperature by rotating the room thermostat dial 14 . Note The temperature is not expressed in degrees. We therefore recommend rotating the room thermostat knob 14 to the maximum heat position. When the temperature in the room reaches the comfort level desired, the thermostat knob may be turned SLOWLY in a counter clockwise direction until the thermostat intervenes, turning off the operation. This programs the unit to the precise level of comfort required which will then be automatically maintained by the thermostat with considerable energy savings. When heating the signal light 15 is off. Note The temperature is not expressed in degrees. We recommend that you turn the thermostat dial to the maximum position. When the desired room temperature has been reached, slowly turn the thermostat 14 in a clockwise direction until it arrives at the position where a click can be heard. The temperature selected in this way will automatically be regulated and maintained, and save energy. When regulating the thermostat, the air conditioning function is temporarily interrupted and the unit continues to operate in fan only mode. In this way, the appliance keeps the air temperature within the room even. TURN THE APPLIANCE OFF TO TURN THE UNIT OFF COMPLETELY, PRESS THE BUTTON 12 (THE SIGNAL LIGHT 11 WILL TURN OFF). 21 ENGLISH 1. A special safety device will delay the start of air conditionig by approximately 3 to 5 minutes when switching between functions or on initial start up. GB 15-01-2001 8:56 Pagina 22 Recommendations RECOMMENDATIONS Follow these recommendations to achieve maximum efficiency from your air conditioning unit: · Close the doors and windows in the room where the unit is functioning. The only exception is in the case of installation through a hole in the wall or window. In this case, you are recommended to allow a small amount of air to enter through a door or window to guarantee an adequate exchange of air. · Keep the appliance a safe distance from combustible surfaces lower the blinds or draw the curtains close doors and windows · Protect the room from direct exposure to the sun's rays by drawing the curtains and/or partially lowering the blinds so as to maximise energy savings. · Do not obstruct the air intake 6 or outlet 1 · Make sure the unit is located on a level floor. [. . . ] If it does not fit your socket, the plug should be cut off from the mains lead, and on appropriate plug fitted, as below. warning: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a mouldedon type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. [. . . ]