User manual DELONGHI PAC 26ECO

[. . . ] Air entering the room through door and window cracks is normally sufficient. is adequate). The unit can also be used as a "temporary" installation for use in any room with a window or french window; this "temporary" installation can be used at any time until it is ready for permanent instalment. N. B. : In either case, check that the unit is resting on at "perfectly level" surface. [. . . ] (16. 00), turn the dial in a clockwise direction (following the direction of the arrow) until the number 16 is lined up with the triangular pointer (the arrows indicates 4:00 P. M. approximately ). PROGRAMMED MODE 1) Select the desired function as shown in the chart overleaf. 2) Press the TIMER key, the "TIMER ON" signal light will come ON. 3) Make sure that the timer indicates the correct time (see instructions on setting). Operating time Funzionamento 20 21 19 N. B. : Never turn the dial in an anti-clockwise direction!The timer is in effect, an electric clock and works only if the plug is connected to the power supply. Whenever the plug is disconnected or there is a power failure, the programmer stops (the clock is then "slow") and must be re-set. 4) Set the operating times by pushing out the notches on the dial corresponding to the period required (each notch represents 15 mins. ) The unit will now switch on and off each day at the selected times. N. B. : To override the programmed operating times, simply press the ON/OFF key (the timer signal lamp ON will go out) NON-PROGRAMMED MODE 1) Press the TIMER ON key again, the TIMER ON signal lamp will go out). For technical reasons, the temperature is not expressed in degrees but by a line increasing in thickness. We therefore recommend that when starting up the appliance, the thermostat be turned to maximum (thick green line = maximum cold). When the desired temperature has been reached, move the cursor slowly away from the maximum cold position until the appliance is switched off by operation of the thermostat. In this way the appliance has been programmed with the exact temperature degree required, which is then maintained automatically by the thermostat. This appliance is fitted with a safety device that blocks its operation if at least 3 minutes have not elapsed from when it was last switched off. 26 16 21 20 19 16 HOW TO START UP THE CONDITIONER (see control panel on the opposite page) Plug the appliance into the mains. signal lamp goes w Press the key for the function required: AIR-COOL. KEY = Ventilation = Automatic climatization AIR-CONDITIONING VENTILATION AUTOMATIC w The Min. speed signal lamp comes on. w The appliance automatically selects the ventilation or the air-conditioning function depending on the room temperature. w Move the cursor to maximum cold position. [. . . ] The function OK signal lamp flashes. · Exhaust hose is blocked · Exhaust hose is bent · Condensator fan is blocked · check whether discharge of air to outside is obstructed in any way. · straighten it · contact Service Centre · There are discrepancies in the control card General switch keeps activating · contact Service Centre · switch off appliance and contact Service Centre The appliance works · Window open but does not cool · Source of heat in room (heater, lamp, etc. ) or the environment room is overcrowded sufficiently · Exhaust hose is disconnected · Thermostat regulated too high · Air filter clogged · The capacity of the conditioner is not adequate for the size of the room · close the window · remove heat source · reconnect tube · lower thermostat setting · clean filter 30 Periodic Servicing (IMPORTANT) This appliance should be de-scaled whenever the calcium deposit becomes excessive (on average after 400 operating hours) or in any event at least once every season. INSTRUCTIONS FOR DE-SCALING You will need: 1/4 liter de-scaling fluid (supplied with appliance) 1 liter clean water = 80% dilution a) Remove the container from the unit and drain away any water left in the collecting tray with the drainage tube. Pour 1/4 liter of de-scaling fluid and 1 l clean water into the collecting tray situated under the container, at the bottom of the unit. [. . . ]