User manual DELONGHI ELECTRIC DEEP FRYER F457CZ

[. . . ] The brown wire must be connected to the terminal marked with the letter L or coloured red. 6 60° I O MIN 140° 160° 180° NO! fig. 8 3 I-GB-F-D-NL-E-P-GR 26-09-2003 15:54 Pagina 9 GB READ THIS INSTRUCTION BOOKLET CAREFULLY BEFORE INSTALLING AND USING THE APPLIANCE. THIS IS THE ONLY WAY TO ENSURE THE BEST RESULTS AND MAXIMUM SAFETY FOR THE USER. DESCRIPTION OF THE APPLIANCE: A. [. . . ] Once the appliance has cooled, using a toothpick or similar, delicately press the safety device reset button "U" marked RESET (see Fig. If the appliance does not start operating again, contact a service centre authorised by the manufacturer. STARTING FRYING · As soon as the light goes off, place the basket "Q" into the oil, lowering it very slowly to prevent the hot oil from spraying or overflowing. · A significant amount of steam will be released: this is completely normal. · It is normal during frying for steam to be released from the cover and condensate to drip form the edge of the cover. · To avoid the risk of burns, never place your hands above the filter on the cover or above the deep fryer when frying. Before opening the cover completely, open it slowly to release the steam from the side. OPERATING INSTRUCTIONS Before using the deep fryer for the first time, carefully clean, using warm water and dishwashing detergent, the basket, the bowl and the cover. The control unit, power cable and heating element may be cleaned using a damp cloth. Check that water does not enter into the control unit and that there is no residual water in the bottom of the removable bowl. Check that the control unit is properly fastened to the deep fryer body. The safety micro-switch "C" will not allow the appliance to be operated if the control unit "Z" is not correctly positioned in the casing "L". The deep fryer is now ready for use. SETTING THE TIMER (if featured) Press the button "G"; the display will show "OO". Keep the button "G" pressed until the required time is shown on the display. Once the required time has been set, release the button "G". The display will start counting down: · from 99 to 01 minutes, the display will count down minute by minute; · from 01 minutes on, the countdown will be in seconds. An audible signal will indicate the end of the set time; to switch off the audible signal, simply press the timer button "G". To change the setting of the timer, reset it by holding the button "G" for a number of seconds. The timer signals the end of the set time, but does not stop the appliance. To replace the battery, access the inside of the casing "L", proceeding as follows: · Remove all the deep fryer components; · Unscrew the two screws that support the timer; · Remove the timer being careful not to let go of the button; · Turn the battery cover in an anticlockwise direction until it is released. · Replace the battery with another of the same type; To re-insert the timer, perform the same operations in reverse. When either replacing or disposing of the appliance, the battery must be removed and disposed according to the laws in force, in that it may damage the environment. FILLING WITH OIL OR FAT · Remove the cover "O" by lifting it by the handle. · Remove the length of cable required to connect the appliance to the mains, from the cable compartment "S" (see Fig. · If oil is used, pour it into the bowl "P" until reaching the maximum level indicated (see Fig. [. . . ] If lard or fat is used, make sure it does not cool down too much, otherwise it will solidify. 12 I-GB-F-D-NL-E-P-GR 26-09-2003 15:54 Pagina 13 CLEANING Before cleaning, make sure that the power plug is disconnected. Never immerse the deep fryer in water and never place it under running tap water (see Fig. The infiltration of water into the control unit may cause electrocution. Check that the oil has cooled down, and then remove the control unit and drain the oil. [. . . ]