User manual DELONGHI EC 200CD. B

[. . . ] The appliance must always be connected to a well-earthed socket rated at 10 A minimum. The manufacturer is not liable for damage caused by inadeguate earthing of the appliance. · In the event of incompatibility between the plug on the appliance and the socket, have the plug replaced with another of the right type by a qualified professional. · Never install the machine in an environment that can reach a temperature less than or equal to 0°C (if the water in it freezes, the coffee maker may be damaged). [. . . ] Allow water to flow until the orange "OK" light goes out, then stop the flow of water by turning the selector knob to the boiler on function (fig 5) 7. To detach the filter holder, turn the handle from right to left. ATTENTION: to avoid spraying, never detach the filter holder while the machine in brewing coffee. NOTE:Pressing the coffee is very important in order to prepare a food coffee. However if you press too hard, coffee will come out slowly and cream will be of a dark colour. If you press to light, coffee will come out too fast and cream will be a very light color. 8. To remove the used coffee, hold the filter locked with the special lever that is built into the handle and let the coffee fall out by knocking the overturned filter holder (Fig. To switch off the coffee machine, turn the selector knob on the appliance to the OFF position "O" (fig. ATTENTION: The first time that coffee is prepared, it is necessary to wash all of the accessories and the internal circuits of the machine, preparing at least five coffees without using the ground coffee HOW TO PREPARE COFFEE USING THE FILTER HOLDER FOR PODS (if fitted): · Preheat the machine as described in the `Preheating the Coffee Machine' section, making sure to leave the filter holder attached to the unit. Following this procedure ensures that the coffee is delivered at a hotter temperature, as well as guaranteeing that the seal of the filter holder gaskets is more effective. · Press the filter holder button and insert the pod into EC190/200 GB 16-12-2002 11:22 Pagina 13 the filter (fig 15). Always follow the instructions on the package of the wafers for the correct positioning of the wafer in the filter. Note: Use pods which conform to the ESE standard: this will be indicated on the packaging by the following symbol: The ESE standard is a system accepted by the leading coffee pod manufacturers, and allows espresso coffee to be prepared simply and without any mess. 3. Attach the filter holder onto the machine, moving from left to right (fig 6). IMPORTANT: Should the coffee holder for pods be used after one for ground coffee, it's necessary to clear the ground coffee remained in the espresso boiler outlet. This cleaning operation is necessary in order to avoid water leackeges from the coffe holder for pods whele coffee is being preposed. 4. Proceed as in points 4, 5 and 6 in the previous section on how to prepare espresso. 5. To remove the pod, press the button on the filter holder and simply lift the pod out 6. To turn the coffee machine off, turn the selector knob on the appliance to the Off position "O" (fig. 14). 6. When the volume of the milk has doubled, fully immerse the milk frother and continue heating the milk (Fig. Once the desired temperature has been reached (the ideal temperature is 60°C), stop the delivery of steam by turning the steam knob in a clockwise direction and at the same time positioning the selector knob at "O" (fig. Add sugar to taste and, if desired, sprinkle a little powdered chocolate on top of the froth. Note:to prepare the coffee after having frothed the milk, first let the boiler cool down, otherwise the coffee will be burnt. To cool the boiler down, place a container underneath the outlet, turn the selector knob to the "espresso" position and allow the water to flow out until the `OK' light goes off. Return the selector knob to the position and then prepare the coffee as described in the previous paragraph. [. . . ] · Change the quality of ground coffee · Only use ground coffee for espresso coffee makers. · Rinse the unit as described in the "descaling" section. The espresso coffee is cold. · The `OK' pilot light was not on when the coffee delivery switch was pressed. · The preheating was not carried out ·The cups were not preheated The pump is too noisy. · The water tank is empty. · The tank is inserted wrongly and the valve at the bottom is not open. [. . . ]