User manual DELONGHI DAP 700E

[. . . ] - The plastic bag containing the appliance must not be left within reach of children as it could represent a hazard. - Before plugging the appliance into the mains electricity supply, make sure the mains voltage corresponds to the voltage indicated on the rating plate. - If the plug fitted to the appliance does not match the power socket, have the socket replaced with a suitable type by a qualified professional. [. . . ] 4. The air then passes through an activated carbon filter which removes odours. The filter is dark grey and is easily distinguished by its highly porous appearance; IONIZER IONIZER PRE-FILTER ACTIVATED CARBON FILTER HEPA FILTER SUPER HEPA FILTER 5. Purified air is then returned to the room through the top mounted grill. The upward movement of filtered air promotes efficient circulation without causing unpleasant drafts; 6. When switched on, an independently controlled ionizer releases a cloud of negative ions into the outgoing filtered air; 7. When coming into contact with the negative ions, small airborne particles become negatively charged. These can then combine with positively charged particles to form larger particles which are subsequently filtered by the purifier; otherwise, the negative particles will be attracted to positively charged surfaces such as walls or floors; 8. The negative ions help create a better balance of ions in the room as, generally, there is a predominance of positive ions over negative ones. So ionizing helps reduce the static electricity created by rugs, carpets, televisions and computer screens. GENERAL FEATURES Voltage Frequency Absorbed power Suitable for rooms of up to Number of fans Fan speed Ioniser control see rating label 30 m3 1 3 · 5 DESCRIPTION OF APPLIANCE A) B) C) D) E) F) G) H) Front panel Washable prefilter HEPA filter Anti-odour activated carbon filter Filtered air outlet grill Handle Power cable Plug I) L) M) N) O) P) Q) Timer light Timer button Ionising button Silent light Standard light Turbo light ON/OFF/fan speed button INSTRUCTIONS FOR USE 1. Unpack the air purifier and place it on a flat, stable surface so that the air inlet (front grill) and air outlet (top grill) are not blocked A good place to position the appliance could be at least a metre away from a wall. Position the filters in the order shown in the diagram: activated carbon filter (black), resting directly against the inside of the purifier so that it stays there, then the HEPA filter, resting against the activated carbon filter and finally the prefilter. 4. Replace the front panel; 5. Check that the voltage in your home corresponds to that indicated on the appliance, then plug the appliance into the mains socket. 6. Turn the appliance on by pressing the ON-OFF/fan speed button (Q), then press the button again to select the required fan speed (quiet, standard, turbo). Quiet mode: use this mode when you want the purifier to work silently. Standard mode: use this mode when you want the purifier to work at medium speed. Turbo mode: use this mode when you want the purifier to work at maximum speed in smoky or particularly dusty atmospheres. 7. To release negative ions into the room with the purified air, press the ioniser button. 8. Programme mode: To activate programme mode, with the appliance on, press the timer button. CLEANING THE APPLIANCE Clean the outside of the air purifier with a soft, clean, damp cloth to remove dust, grime and fingerprints. The front grill and prefilter within it can be removed and washed separately in warm, soapy water (NOT in a dishwasher). Remember that the efficiency of your purifier depends largely on the condition of the filters. If a considerable amount of dust and other dirt has accumulated, remove the filter from the grill and wash it by hand in warm soapy water. [. . . ] WARNING - THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and yellow: Earth Blue: Neutral Brown: Live If the plug is a moulded-on type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. In the event of losing the fuse cover, the plug must NOT be used until a replacement fuse cover can be obtained from your nearest electrical dealer. The colour of the correct replacement fuse cover is that as marked on the base of the plug. [. . . ]