User manual DELONGHI CORDLESS METAL TRADITIONAL KETTLE KBG24

[. . . ] · Do not use the kettle for any purpose other than heating water. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury. · Position the kettle properly on the power base before switching on. · Use the kettle only with the power base supplied (and vice versa). [. . . ] When wiring the plug, ensure that all strands of wire are securely retained in each terminal. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size. This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference. WARNING - THIS APPLIANCE MUST BE EARTHED Green and Yellow to Earth Blue to Neutral , , yy , , yy , , yy 4 13 amp Fuse Brown to Live Cord Clamp Kettle UK 29-06-2001 8:33 Pagina 5 BEFORE USE · Remove all packaging from the kettle and power base. "Removing the scale filter" · Fill the kettle and boil. · The boiled water should be discarded and the kettle rinsed out with cold water. This procedure should be carried out three times, to remove any manufacturing dust, etc. · After the kettle has been rinsed out, re-fit the filter (fig. 3). 1 IN USE Power base with 360° access 2 3 With the specially designed power base and central connector, you can now set the kettle on the base at any angle, from any position. · Release cord from storage base and adjust length by winding around the base to give the correct cord length to reach the plug socket to be used (fig. · Do not leave loose cord hanging over the edge of work surfaces. CORD EXIT 4 Filling · Remove the kettle from the base unit before filling. Do not fill with less than 0, 25 litre of water to prevent the kettle running dry while operating; misuse of this kind will shorten the life of the element. Do not fill with more than 1, 7 litres of water (up to the MAX indication located inside the kettle) (fig. If the kettle is overfilled, there is a risk that boiling water may be ejected causing burns. MAX 1. 7 litres MIN 0. 25 litres 5 5 Kettle UK 29-06-2001 8:33 Pagina 6 Switching on · · · · · Plug the power base into the mains socket. 0 The kettle will automatically switch off once the water is boiled I (the ON/OFF switch will click upwards and the lights will go out). 6 · To turn the kettle off before the water boils, you may move the ON/OFF switch up to the OFF position, or simply lift the kettle from its base - it will switch off and the switch will return to the OFF position automatically. Pouring · Remove the kettle from the power base and carefully pour out the water. · When you lift the kettle from the base, you may see moisture on the top surface of the base. This is condensation from the steam that causes the kettle to turn off automatically after boiling. Condensation on the base is perfectly normal, and should not be a cause for alarm. SAFETY DEVICES 1) Automatic ON/OFF switch Your kettle is fitted with an ON/OFF switch which automatically switches off once the water has boiled. If the kettle has just boiled, wait a minute or so before re-boiling the kettle. [. . . ] You should remove and clean the water filter when you notice any deposits being left on the filter or if the pouring efficiency is impaired. Removing the scale filter · Allow the kettle to cool down fully. · Make sure that your hands are clean and free from soap, cream or anything which might taint the water. · Empty the kettle and remove the filter by pushing as shown in fig. 3). To clean the scale filter It is vital to clean and descale regularly in order to maintain good working order · Use a proprietary descaling product e. g. [. . . ]