User manual DELONGHI CORDLESS KETTLE KBX3010

[. . . ] · To close the lid push it on the upper part. Fig. 4 Push Fig. 5 3 Kettle KBC3010/ KBX3010 182IDL 20-09-2002 8:04 Pagina 4 Switching on Plug the power base into the mains socket. The kettle will automatically switch off once the water is boiled (the ON/OFF switch will click upwards and the light will go out). · To turn the kettle off before the water boils, you may move the ON/OFF switch up to the OFF position, or simply lift the kettle from its base - it will switch off and the switch will return to the OFF position automatically. · · · · · 1, 7 L MAX 1. 7 litres 1, 0 L 0, 6 L MIN 0. 6 litres Fig. 6 Pouring · Remove the kettle from the power base and carefully pour out the water. [. . . ] On traditional kettle elements, scale forms a hard white "crust" which adversely affects performance and reduces the life of the element. As soon as you notice a film forming on the water, or when cleaning the filter, if you notice a film on the walls or the element, simply rinse the kettle and wipe it out. Scale filter Your kettle is fitted with a scale filter to prevent loose particles of scale being poured into your beverage. This filter is both removable and washable. The frequency with which you will need to clean any scale deposits from your filter will depend on the hardness of water in your area and how often you use the kettle. You should remove and clean the water filter when you notice any deposits being left on the filter or if the pouring efficiency is impaired. Removing the scale filter · Allow the kettle to cool down fully. · Make sure that your hands are clean and free from soap, cream or anything which might taint the water. Remove the filter by pushing the catch down and lifting up (see figure 1) · Rinse under a tap whilst brushing with a soft brush (fig. 3). 5 Kettle KBC3010/ KBX3010 182IDL 20-09-2002 8:04 Pagina 6 To clean the scale filter It is vital to clean and descale regularly in order to maintain good working order · Use a proprietary descaling product e. g. We recommend using citric acid crystals as follows: · Pour into kettle about 50 gr. of citric acid crystal and then fill with water up to the max level indicated and then boil. If the filter requires descaling, remove the filter and place into the citric acid solution. · Ensure that the electrical connections are completely dry before using the kettle. · Citric acid crystals are available from most pharmacies. Safety Warnings Please read these instructions before operating and retain for future reference. · Ensure that your mains supply voltage is the same as that marked on the underside of your kettle. · To protect against electrical hazards do not immerse the mains lead, plug power base or kettle in water or any other liquid. · Take care when pouring - do not over-tilt the kettle as water may enter into the switch mechanism. · Water can remain hot for a long time after boiling and can present a scald hazard. Keep the kettle and the mains lead away from the edge of the work surface and out of the reach of children. · Do not allow the mains lead to hang over the edge of the table or work surface, or anywhere it may be accidentally caught or tripped over. · Close supervision is necessary when any appliance is used near children. · Remove the plug from the mains socket when not in use and before cleaning. [. . . ] If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. N. B. We recommend the use of good quality plugs and wall sockets that can be switched off when the machine is not in use. important: the wires in the mains lead fitted to this appliance are coloured in accordance with the following code: GREEN AND YELLOW BLUE BROWN EARTH NEUTRAL LIVE Warning 8 Kettle KBC3010/ KBX3010 182IDL/09. 02 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. [. . . ]