User manual DELL 5100MP

[. . . ] c o m Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your projector. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. injury, or death. CAUTION: A CAUTION indicates a potential for property damage, personal ____________________ Information in this document is subject to change without notice. Reproduction in any manner whatsoever without the written permission of Dell Inc. Trademarks used in this text: Dell , the DELL logo, Dimension, OptiPlex, Dell Precision, Latitude, Inspiron, DellNet, PowerApp, PowerEdge, PowerConnect, and PowerVault are trademarks of Dell Inc. ; DLP and Texas Instruments are trademarks of Texas Instruments Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation; Macintosh is a registered trademark of Apple Computer, Inc. [. . . ] b Verify the setting is 1024 x 768 pixels for the external monitor port. If you experience difficulty in changing resolutions or your monitor freezes, restart all the equipment and the projector. If you are not using a Dell portable computer, see your documentation. The screen does not display your presentation If you are using a portable computer, press . Image is unstable or flickering Adjust the tracking in the OSD Computer Source tab. Image has vertical flickering bar Image color is not correct Adjust the frequency in the OSD Computer Source tab. · If your graphic card output signal is sync on Green, and you would like to display VGA at 60Hz signal, please go into OSD select Management, select Signal Type and then select RGB. · Run the Self-diagnostic test (see " Selfdiagnostic for video ") for preliminary diagnostic on image color problem. Ensure that the colors of the test pattern are correct. 1 Adjust the focus ring on the projector lens. 2 Ensure that the projection screen is within Image is out of focus the required distance from the projector (4. 9 ft [1. 5 m] to 39. 4 ft [12 m]). 46 Troubleshooting Your Projector Problem (continued) The image is stretched when displaying a 16:9 DVD Possible Solution (continued) The projector automatically detects a 16:9 DVD and adjusts the aspect ratio to full screen with a 4:3 (letter-box) default setting. If the image is still stretched, adjust the aspect ratio as follows: · If you are playing a 16:9 DVD, select 4:3 aspect ratio type on your DVD player (if capable). · If you cannot select 4:3 aspect ratio type on your DVD player, select 4:3 aspect ratio in the Image Settings menu in the OSD. Image is reversed Lamp is burned out or makes a popping sound Select Management from the OSD and adjust the projection mode. When the lamp reaches its end of life, it may burn out and may make a loud popping sound. If this occurs, the projector does not turn back on, and displays Lamp Defective in the LCD display until the lamp is replaced. If the LAMP light is blinking orange, the lamp cover is not closed properly. A projector fan has failed and the projector will automatically shut down. If so, replace with 2 new AA batteries. LAMP light is solid orange Interlock failed TEMP light is solid orange TEMP light is blinking orange The remote control is not operating smoothly or in very limited range Troubleshooting Your Projector 47 www. dell. com | support. dell. com Self-diagnostic for Video Dell 5100MP Projector provides self-diagnostic test of the projector video display (for Video, S-video, Component-i). Use this advanced feature for preliminary selfdiagnostic on your projector when encountering a display problem for video. 1 After turning on the projector, press "+" and "-" buttons on the control panel simultaneously for 3 seconds and release the buttons when screen goes blank. 2 Press "+" and "-" buttons again to exit the diagnostic mode. 3 While in Self-diagnostic mode, the screen will run a seven-color-cycle test as following: Red--> Green--> Blue--> White--> Watchet Blue--> Dark Green--> Yellow. Contact Dell if the colors are not displayed correctly. Changing the Lamp Replace the lamp when you see "Lamp is approaching the end of its useful life in full power operation. If this problem persists after replacing the lamp, contact Dell. CAUTION: The lamp becomes very hot when in use. Do not attempt to replace the lamp until the projector has been allowed to cool down for at least 30 minutes. [. . . ] . . . . 10 10 11 12 12 12 13 13 14 14 15 16 17 M1 D-sub/USB D-sub D-sub DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 20 21 22 23 25 28 28 30 31 33 33 34 34 35 35 36 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 . . . . . . . . . . . . . . . . . . . 47 48 . . . . . . . . . . . . . . . . . . . . . . 4 5 . 91 5 6 1 1. 8 ( 3 ) 1. 8 M1 D-sub/USB 2 S-Video 1. 8 1. 8 RCA 1. 8 1. 8 M1-A HDTV 7 www. dell. com | support. dell. com ( ) (2) 1 2 3 4 5 6 7 8 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RJ45 HDMI VGA M1 S-video VGA RS232 /RF 12 DC BNC 9 www. dell. com | support. dell. com M1 D-sub/USB 1 2 M1A D-sub/USB USB Dongle USB USB Dongle 37 10 D-sub D-sub 1 2 D-sub D-sub USB Dongle USB USB Dongle 37 11 www. dell. com | support. dell. com DVD M1 HDTV DVD 1 2 M1 HDTV D-sub YPbPr DVD 1 2 D-sub YPbPr Dell D-sub YPbPr 12 RCA RCA DVD 1 2 RCA RCA Dell RCA RCA S-video DVD 1 2 S-video 13 www. dell. com | support. dell. com DVD 1 2 BNC VGA DVD 1 2 BNC VGA Dell BNC VGA 14 1 2 3 12V DC 1. 7mm(ID) x 4. 00mm(OD) x 9. 5mm (shaft) 12V DC 12V DC 15 www. dell. com | support. dell. com RS232 1 2 RS232 Dell RS232 16 RS232 1 2 3 RS232 RS232 Dell RS232 17 www. dell. com | support. dell. com 18 3 1 2 9 3 ( 23 )Dell 30 4 ( DVD ) . . . [. . . ]