User manual DEI RVM680 Installation Guide

[. . . ] Contact your authorized dealer to obtain the service charge for your unit. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. [. . . ] Hot Foot adapter Note: This manual makes reference to optional Directed Video parts not included with this product. 6 © 2001 Directed Electronics, Inc. Basic Operation 2 1 4 56 43 MONITOR DESCRIPTION 1. Power/Source button - Press to turn the monitor on/off or change video source. I MAINTENANCE Keep the monitor clean and free of dust and moisture and it will provide years of trouble free operation. Do not allow any cleaning fluids on the monitor screen or bezel, they may contain chemicals that can harm the finish and diminish the picture quality. To clean the monitor, simply use a soft, dry cloth and gently wipe away any dirt. Avoid applying too much pressure to the screen when cleaning as it can result in damage. 3. Also adjusts TV/CATV channel up and down when TVM300 module is connected. LED indicator light - When turned on the light is blue; when on standby the light is red. 5. 6. © 2001 Directed Electronics, Inc. 7 On-Screen Menus The Setup Menu is a list of programming selections that control system operation and screen settings. To change the settings described, follow the directions in the on-screen menus section or the special instructions in each menu. SELECTION CHANNEL (TVM300 ONLY) DIMMER DESCRIPTION AND OPERATION I I I I I I Change TV channels. Use CHDN/CHUP buttons to change channels Change illumination for day or night viewing. WIDESCREEN (16:9) - Wide screen videos will appear undistorted and fit the full screen. Normal videos (4:3) will be stretched from the sides to fit the full screen and appear distorted. NORMAL (4:3) - Normal videos will appear undistorted in the center with bars at both sides. Wide screen videos (16:9) will shrink to fit into the same area and make the image appear taller. The center of the picture will appear normal with the edges stretched to fit the full screen and appearing slightly distorted. The picture will be zoomed in to fit the full screen from side to side. The picture will remain undistort ed, but a portion of the top and bottom will be cut off. BLUE - Changes the OSD to Blue. PICTURE Note: To adjust use the monitor's UP/DOWN buttons or the remotes (+)/(-) buttons. I I I I I I SCREEN (RVM700 ONLY) I I I OSD COLOR I I I I © 2001 Directed Electronics, Inc. 9 SECURITY (ESP/ESP2 ONLY) NOTE: This menu contains selections that have additional settings. I I I ESP/ESP2 programming and zone information. (Always displays the last zone triggered only. ) See the Assign Trigger Names menu. See the Trigger Names menu. SETUP (MCB1000 ONLY) NOTE: This menu contains selections that have additional settings. This menu is used for initial system setup only. I I I I IMPORTANT! Any changes in the following menus must be written into the MCB1000 and ESP/ESP2 software. Before the menu is exited the "write to system" procedure must be completed. SYSTEM SETTINGS MENU SELECTION PASSIVE/ACTIVE ARMING (passive) DESCRIPTION AND OPERATION Program the ESP/ESP2 security system to arm by itself or if its remote must be used for arming (active). [. . . ] Place one of these against the mounting bracket (2) and guide the other end of the monitor into the bracket on the other side of the monitor. Tilt the monitor up into the mount and press firmly until a click is heard. The connector at the back of the monitor is selfguiding and will connect automatically to the monitor connector (4). The Hot Foot adapter is for use with the MMS1 Universal Monitor Mounting Pedestal. [. . . ]