User manual DEI AUTOMATE AM1 Owners Guide

[. . . ] SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE © 2005 directed electronics, inc. i AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS, INC. [. . . ] This progressive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the system is armed, while still providing instant response (even if the door is immediately closed). note: If programmed for instant trigger, the horn will output full trigger response after the door has been opened (see Programming Options) Turning on the ignition key triggers the same progressive response as opening a door. If equipped, the starter interrupt prevents the vehicle's starter from cranking. note: The vehicle may already be equipped with a starter kill relay from the factory. 4 © 2005 directed electronics, inc. disarming To disarm the system, unlock the doors using your factory keyless transmitter. If the horn sounds either four or five times when disarming, refer to the Diagnostics section of this guide. This is called Tamper Alert. disarming without a transmitter This feature allows you to override the system without the transmitter should it be lost, damaged or disabled. To do this, you must have the vehicle's ignition key and know where the integrated LED/Valet® switch is located. The Valet® switch is activated by pressing the LED status indicator. Integrated LED/Valet® switch LED status indicator Turn the ignition to the "run"position. Press and release the integrated LED/Valet® switch, within 10 seconds. After a few seconds the LED will stop flashing and the vehicle should start. Turn the ignition off and try again. DRW-35 note: The setting for the number of times the integrated LED/Valet® switch must be pressed is set in the Programming Section of this guide. © 2005 directed electronics, inc. 5 valet mode ® You can prevent your system from arming, by using Valet® Mode. In Valet® Mode, the system will not arm, even with the transmitter, but all convenience functions (door locks, trunk release, etc. ) will work normally. To enter or exit Valet® Mode with the integrated LED/Valet® switch: Turn ignition to "on" position, turn to "off" position. Press and release the integrated LED/Valet® switch within 10 seconds. The LED will turn off when exiting Valet® Mode. DRW-35 then remote valet ® Remote Valet® is a convenient feature that makes bypassing the security system easier. This feature makes it possible to exit or enter Valet® Mode using your factory keyless transmitter. The only ways to reset a bypassed zone are for it to not trigger for 60 minutes or to turn on the ignition. If testing your system, it is important to remember that this circuitry can cause zones to be bypassed and appear to stop working. If five chirps are heard when disarming, false alarm protection has engaged. If you wish to clear the memory, turn the ignition key on. 8 © 2005 directed electronics, inc. diagnostics The microprocessor at the heart of your system is constantly monitoring all of the switches and sensors connected to it. It detects any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. arming diagnostics If the system is armed with an input active (door open, sensor triggering, etc. ) the unit will chirp once when arming and then one more time a few seconds later. This is called bypass notification. note: Bypass notification will not occur if chirps have been programmed OFF. The system will ignore the input that was active when it was armed until it goes away. For example, if your car has interior light exit delay, and you arm the system before the interior light goes out, you may get bypass notification. Once the light goes out, however, the doors are monitored normally. disarming diagnostics Extra disarm chirps are the tamper alert. [. . . ] Press the integrated LED/Valet® switch the programmed number of times within 10 seconds. Turn the ignition off and on and try again. To enter or exit Valet® Mode Turn ignition to "run" position, then turn to "off" position. Press and release the integrated LED/Valet®switch within 10 seconds. The status LED will light solid if you are entering Valet® Mode, and it will go out if you are exiting Valet® Mode. Remote Valet® Open any door. [. . . ]