User manual DCS CS-364G INSTALLATION GUIDE

[. . . ] CS COOKTOP SERIES Installation Guide MODELS: CS-366 CS-364GL CS-364G CS-484GG CS-486GL CS-486GD CS-485GD A MESSAGE TO OUR CUSTOMERS Thank you for selecting this DCS CS Cooktop. Because of this appliance's unique features we have developed this Installation Guide. It contains valuable information on how to properly install your new appliance for years of safe and enjoyable cooking. For your convenience, product questions can be answered by a DCS Customer Service Representative by phone: 1-888-281-5698, Fax: 714-372-7004, email: support@dcsappliances. com, or by mail: DCS Attention: Customer Service 800 Skylab Road Huntington Beach, CA 92647 www. dcsappliances. com WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. PRECAUTION Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. FOR YOUR SAFETY IF YOU SMELL GAS: Do not try to light any appliance. [. . . ] 1 CS Cooktop Models A 47-7/8" 35-7/8" B C D 26-1/2" 8-7/16" 46-5/16" 26-1/2" 8-7/16" 34-15/16" E 22-3/4" 22-3/4" F 8" 8" G H 7/8" 0-2-1/2" 1/2" 0-2-1/2" 13" Max. to Combustible Material , Each Side D Cooking Surface 16" E I CAUTION 36" Min. to combustible material , from cooking surface CS 48 Models CS 36 Models 8 CABINET PREPARATION STEP 3: (CONTINUED) 6) Cut the openings for the following installation: Standard counter top installation, see Fig. 5B NOTE: If the deck is used, the sides or bottom of the cutout may be solid combustible or non-combustible material. If the bottom is solid, provide a 6" x 6" cutout in the left rear corner for the gas inlet and power cord clearance. Front projects outward shown Front projects outward as as shown from standard depth cabinet. from standard depth cabinet. Flush with cabinets Flush with cabinets Front flush with cabinets; minimum Front flush with cabinets; a a minimum of 25 3/4" cabinet depth required of 25 3/4" cabinet depth required Fig. It must be plugged into a mating grounding type receptacle, connected to a correctly polarized 120 Volt circuit. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the installer to have the existing receptacle changed to a properly grounded and polarized receptacle in accordance with all applicable local codes and ordinances by a qualified electrician. In the absence of local codes and ordinances, the receptacle replacement shall be in accordance with the National Electrical Code. The third prong should not, under ANY circumstances, be cut or removed. GAS REQUIREMENTS Verify the type of gas supplied to the location. The cooktop are shipped from the factory set up and adjusted for natural gas or LP (propane), depending on specific model ordered. The unit cannot be converted. NATURAL GAS Connection: 1/2" N. P. T. , Minimum 5/8" dia. Pressure: 6" to 14"W. C. LP GAS Connection: 1/2" N. P. T. , Minimum 5/8 dia. A regulator is required at the LP source to provide a maximum of 14"W. C. to the cooktop regulator. 12 HOOK-UP TO GAS SUPPLY STEP 6: HOOK-UP A manual valve must be installed external to the appliance, in an accessible location from the front for the purpose of shutting off the gas supply. Make sure the gas supply is turned off at the wall valve before connecting the appliance. The gas supply connections should be made by a qualified technician and in accordance with local codes or ordinances. In the absence of a local code, the installation must conform to the National Fuel Gas Code ANSI 223. 1-1988, latest edition. To prepare the unit for connection to the gas supply, thread the supplied 1/2" pipe nipple into the elbow on the end of the manifold. The elbow is located inside the chassis of the unit, on the end of the manifold, facing down. It is accessible through the square cutout in the left rear corner of the chassis bottom. Connect the outlet of the regulator to the exposed end of the nipple, connect the flex line from the gas supply to the inlet side of the regulator. [. . . ] Each burner lights satisfactorily, both individually and with other burners. Flame adjustment made on air shutter of griddle, or grill burner, (figs. Drip trays are properly in place and pull out freely (Not all models). Burner grates correctly positioned, level, and do not rock. 15 CS 36" / 48" WIRING DIAGRAM 16 CS 36" / 48" SCHEMATIC 17 CS 485 WIRING DIAGRAM 18 CS 485 WIRING SCHEMATIC 19 HOW TO OBTAIN SERVICE For warranty service, contact DCS Customer Service at (888) 281-5698. [. . . ]